Panasonic DVD-F85S Operating Instructions Manual

Getting startedRQT69779The remote control∫ Batteries≥Insert so the poles (i and j) match those in the remote control.≥Do not use rechargeable type batteries.Do not:≥mix old and new batteries.≥use different types at the same time.≥heat or expose to flame.≥take apart or short circuit.≥attempt to recharge alkaline or manganese batteries.≥use batteries if the covering has been peeled off.Mishandling of batteries can cause electrolyte leakage which can damageitems the fluid contacts and may cause a fire.Remove if the remote control is not going to be used for a long period oftime. Store in a cool, dark place.∫ UseAim at the sensor (➜ page 5, Control reference guide), avoidingobstacles, at a maximum range of 7 m (23 feet) directly in front of the unit.The QUICK SETUP screen appears when you press [SETUP] the firsttime after purchase and assists you to make necessary settings.PreparationTurn on the television and select the appropriate video input on thetelevision to suit the connections for the player.[1] Press [Í] to turn on the unit.[2] Press [SETUP] to show the QUICK SETUPscreen.[3] Press [3, 4] to select the menu language andpress [ENTER].[4] Press [3, 4] to select “Yes” to continue andpress [ENTER].[5] Press [3, 4] to select the item and press[ENTER].≥Audio Language (➜ page 20)≥Subtitle Language (➜ page 20)≥TV Type (➜ page 20)≥TV Aspect (➜ below)≥Progressive Out (➜ page 20)≥Speaker Setting (➜ page 20)≥PCM Digital Output (➜ page 21)[6] Press [ENTER] and then [SETUP] to end thesettings.To return to the previous screenPress [RETURN].To access this screen again later➜ page 20, Others—QUICK SETUP∫ TV AspectSelect “4:3” (regular) or “16:9” (widescreen) to suit your television.If you have a regular 4:3 television, you can also select how video onsome discs is shown (➜ page 20, Video—TV Aspect).≥4:3 Pan&Scan (Factory preset)Widescreen software is expanded to fill the screenof a 4:3 aspect television (unless prohibited by theproducer of the disc).≥4:3 LetterboxWidescreen software is shown in the letterbox styleon a 4:3 aspect television.∫ To enjoy progressive video1. Connect to the component video input terminals on a 480Pcompatible television. (Video will not be displayed correctly ifconnected to an incompatible television.)2. In QUICK SETUP, set “Progressive Out” to “Enable”.3. Change Video output mode to “480P” (➜ page 18).≥All televisions manufactured by Panasonic and that have 480P inputconnectors are compatible. Consult the manufacturer if you haveanother brand of television.≥If the unit is connected to the television through VIDEO OUT or SVIDEO OUT, output will be interlace, irrespective of the settings.R6, AA, UM-3Quick setup[1][3] • [4][5] • [6][2] • [6]RETURNCANCEL1 2 34 5 67 8 90 10DISC1 DISC2 DISC3DISC4 DISC5SLEEPDISCSETUP OPEN/CLOSESEQUENTIALFL SELECTGROUPDIRECT NAVIGATORTOPMENUDISPLAYSUBTITLE AUDIO ANGLE/PAGE QUICK REPLAYRETURNMENUENTERPLAY LISTSKIPSLOW/SEARCHSTOPPLAYPAUSEPOWER Í /I AUDIO ONLY DISCDOUBLE RE-MASTER ;∫ 1 :/6 5/9 DISC EXCHANGE DISC SKIP <OPEN/CLOSE1 2 3 4 5[1]SELECTSETUPENTER RETURNQUICK SETUPSelect the menu language.EnglishFrançaisEspañol