Panasonic Diga DMR-EX99V Operating Instructions Manual

Contents

79VQT2J46Setting menus§1 This is displayed only when “Digital Channels” is selected in “TVGuide Type”.§2 When “Digital Channels” is selected in “TV Guide Type”§3 When “Analogue Channels” is selected in “TV Guide Type”§1 The timer recording programmes are also cancelled.§2 Recording on the HDD will not be deleted.Auto Standby after OTR[On] This unit is turned to standby mode when this unit is notoperated for approximately 5 minutes after completingOne Touch Recording (> 22).[Off]Auto Standby after Copy[On] This unit is turned to standby mode when this unit is notoperated for approximately 5 minutes after completingcopy (> 58-67).[Off]RF OUT ( Aerial Signal )[On] Broadcast signals are output from this unit.TV can receive broadcast signals even if this unit is instandby mode when connecting TV with this unit usingthe RF cable (> 83).[Off] Press [2, 1] to select “Yes” when the confirmationmessage is displayed.Broadcast signals are not output from this unit to reducestandby power consumption.≥Power consumption is lowered additionally when“Power Save in Standby” is activated.≥If this unit turns into standby mode when connecting TVwith this unit using the RF cable, proper broadcastimages do not appear on TV.DivX RegistrationYou need this registration code to purchase and play DivXVideo-on-Demand (VOD) content (> 42).TV Guide TypeThis unit can receive either of the TV Guides for the digital oranalogue broadcasts.Press [2, 1] to select “Yes” and press [OK].≥It will go into Standby status once, and the power will be turnedon again automatically. This procedure may take a few minutes.≥All of the TV Guide data for digital broadcasts and timerrecording settings will be erased.[Digital Channels] [Analogue Channels]System UpdateIn order to update this unit’s software, the TV Guide download, andto support system changes made by broadcasts, this unitperiodically performs software updates.Press [OK] to show the following settings.≥Only the TV Guide for digital broadcast can be downloaded withthis setting. Refer to page 13 for analogue broadcasts.≥Update data and TV Guide download information are sent by anunscheduled digital broadcast. In order to receive these updates,you must be able to receive digital broadcasts.≥An update will take approximately 60 minutes. While the updateis in progress, “SW-DL” appears on the unit’s display. You cannotoperate the unit until the update is complete. Removing the ACmains lead while the update is in progress may damage the unit.≥TV Guide download will take approximately 60 minutes. Whilethe TV Guide download is in progress, “GUIDE” appears on theunit’s display. The TV Guide download can be interrupted byswitching on the unit.TV Guide Download in Standby§1[On] When you set this unit to standby mode, TV Guide data isdownloaded automatically.[Off]≥In the area where GUIDE Plus+ system is available, the settingis fixed to “On” automatically.Software Update in Standby[On] When you set this unit to standby mode, softwareupdates are downloaded automatically.[Off]TV Guide/Software search period§2Software Search Period§3Selects the time to automatically perform TV Guide downloadand updates when the unit is set to standby mode. This can onlybe set when “TV Guide Download in Standby” or “SoftwareUpdate in Standby” is set to “On”.≥If there is a programmed recording set for the time you haveselected, the programmed recording will be given priority.In the area where GUIDE Plus+ system is not available:[Automatic]§[02:00–06:00] [06:00–10:00] [10:00–14:00][14:00–18:00] [18:00–22:00] [22:00–02:00]In the area where GUIDE Plus+ system is available:[Automatic]§ [Daytime] (06:00-22:00)§ The unit will give priority to searching for TV Guide downloadand update data at midnight.Software Update Search NowStart the search for new software manually.A new software version is announced by a message. Do not turnyour unit off during the update. This could result in the loss ofdata. A message shows that the update has finished.≥If applicable update data is found, press [2, 1] to select “Yes”and press [OK].[For]Germany,[Austria,[Italy[and[Spain]GUIDE Plus+ Data Download Now§1Start downloading GUIDE Plus+ data.≥If this is performed in standby mode for timer recording, timerrecording may not work correctly.[For]Germany,[Austria,[Italy[and[Spain]GUIDE Plus+ System Information§1You can check the condition of GUIDE Plus+ system of this unit.[For]Germany,[Austria,[Italy[and[Spain]Post Code§1You can input the postal code which is necessary to downloadarea specific information of GUIDE Plus+ system.Initialize≥Press [OK] to show the following settings.Shipping Condition§1, §2All the settings except for the language settings, ratings level,ratings PIN, Slideshow Settings, and clock settings, etc. return tothe factory preset.[Yes] [No]Default Settings§1, §2All the settings other than the tuning settings, clock settings,country settings, language settings, disc language settings,ratings level, ratings PIN, remote control code, etc. return to thefactory presets.[Yes] [No]