Panasonic NV-VP33 Series Operating Instructions Manual

Also see for NV-VP33 Series: Operating instructions Operating instructions

Contents

Getting Started11RQTV0057Tuning the TV to Your UnitThe unit supplies a signal to the TV via the RF coaxial cable onchannel AU28s 69 or NZ21s 69. It is possible to view the unit’spicture on your TV in the same way that you watch TV broadcasts.The unit is fitted with its own tuner (just like a normal TV) and can bepreset to receive up to 99 TV broadcast stations.≥Press [VHS].¬ If you have connected the unit to the TV through the audio/video output socketsYou do not need to follow the procedure below. To view the picturesfrom the unit, set to the AV mode on the TV with [AV].The local TV broadcast channels 2, 7, 9, 10 and 28 are factory-preset in the unit.That is, if you can receive TV broadcasts on VHF channels 2, 7, 9,10 and UHF channel 28, these are already tuned on the programmepositions with the matching numbers.........................................................................................................................................................................................................................[1] Press [ÍVHS] to turn onthis unit..........................................................................................................................[2] Hold down [MENU] for 5seconds or more..........................................................................................................................[3] Set the TV to an unusedposition for the unitviewing channel.≥Tune the TV until the display shown on the right appears. Referalso to the TV’s instructions regarding tuning.........................................................................................................................................................................................................................[4] Press [MENU].When the unit is turned on afterconnecting the aerial cable and themains lead for the first time, tuningstarts automatically.≥If the unit is turned on with the aerialnot connected, all channels areskipped...............................................................................................................................[1] Press [ÍVHS] to turn onthis unit...............................................................................................................................[2] Set the TV to an unusedposition for the unitviewing channel...............................................................................................................................[3] Press [MENU].ª To cancel Auto Tuning halfway throughAuto Tuning will stop halfway by turning the unit off, pressing[MENU], playback or power failure.¬ If Auto Tuning stops halfway by turning the unit off, playbackor power failure≥Disconnect the mains lead and then reconnect it.≥Turn on the unit. Plug in Auto Tuning restarts.¬ To set the channels manually (l 21)ª To restart Plug in Auto Tuning≥Turn the unit on.≥Make sure there is no video cassette in theunit.1) Keep both [JCH] and [ICH] on theunit pressed simultaneously for 3seconds or more until the channel onthe unit’s display changes to 1.2) Disconnect the mains lead and then reconnect it.3) Turn on the unit. Plug in Auto Tuning restarts.You can change the RF output channel,for example, when interference occurs onthe picture after tuning..........................................................................................................................[1] Press [MENU] for 5seconds or more..........................................................................................................................[2] Press [JCH] or [ICH ] toselect the channel(AU28s69, NZ21s69).≥Each time you press [JCH] or[ICH], (l below).≥Set to “ss” (RF OFF) when youuse the audio/video cable for theconnection.≥You can also use the numeric buttons.Example: “28”; [2]l[8].............................................................................................[3] Retune your TV tothe new RFchannel for theunit..............................................................................................[4] Press [MENU] toexit the settingmode.Note:≥Even if the RF output channel has been changed, it is notnecessary to perform Auto Tuning.Pre-programmed TV Channels (for NV-VP33GL/Australia)Plug in Auto Tuning (for NV-VP33GN/New Zealand)END : MENUPanasonicEND : MENUCH 22 SEARCH 21END : MENUAUTO TUNING ISCOMPLETED.Disappears 1To Change the RF Output ChannelEND : MENUPanasonicNV-VP33GLNV-VP33GN28 … 69(RF OFF)NV-VP33GL21 69(RF OFF)NV-VP33GN