Panasonic PT-LC56E Operating Instructions Manual

Panasonic PT-LC56E Operating Instructions Manual Manual pdf 22 page image

ENGLISH -43 Adjustments and settings42-ENGLISHUse the F and G buttons on theprojector or remote control unit toselect an item, then press the I orH buttons to change the setting.OSDONThe current input name is displayedin the top-right corner of the screenwhen the input signal is changed.OFFUse this setting when you do notwant the current input name to bedisplayed.AUTO SIGNALThis should normally be set to ON.ONAUTO SETUP will be carried outautomatically when the input signalis changed.OFFAUTO SETUP will not functionwhen the input signal is changed.AUTO KEYSTNThis should normally be set to ON.ONDuring automatic setup, the angle oftilt of the projector is detected andkeystone distortion is correctedautomatically.OFFUse this setting when you do notwant automatic keystone correctionto be carried out during automaticsetup, such as when the screenitself is at an angle.AUTO RGB INThis should normally be set to ON.ONDuring automatic setup, theprojector selects whichever one ofthe RGB1 IN or RGB2 INconnectors has a signal being input,and uses that signal for projection.(If a picture is being projected, thesignal source is not automaticallychanged.)OFFUse this setting when you do notwant the signal source to bechanged automatically duringautomatic setup.RGB2 SELECTThis setting is used to select thefunction of the RGB2 IN/RGB1 OUTconnector.R G B 2 S E L E C T I N P U T[O U T P U TRGB/YPBP RThis should normally be set toAUTO. RGB or YPBPR is selectedautomatically depending on thesynchronising signal status.When HDTV, 525p (480p), 525i(480i), 625i, 750p, and someVGA480 signals are beinginput, select “RGB” or “YPB P R” inaccordance with the input signal.VGA60/525PWhen a VGA60 or 525p RGB signalis being input, select the signal inaccordance with the input signal.SXGA MODEThis setting is only for an SXGAsignal.SXGASelect this item normally.SXGA+When the projected image iscontracted vertically, select thisitem.BLACKBOARD (PT-LC80E only)Set to “ON” when PICTURE MODEis set to BLACK-BD. (Refer to page35.)BACK COLORThis sets the colour which isprojected onto the screen when nosignal is being input to the projector.FRONT/REARThis setting should be changed inaccordance with the projectorsetting-up method.Set to “FRONT” when using anormal reflective screen with theprojector positioned in front of thescreen, and set to “REAR” whenusing a translucent screen with theprojector positioned behind thescreen.DESK/CEILINGThis setting should be changed inaccordance with the projectorsetting-up method.Set to “DESK” when setting up theprojector on a desk or similar, andset to “CEILING” when suspendingthe projector from the ceiling usingthe ceiling bracket which is soldseparately.FAN CONTROLSet FAN CONTROL to “HIGH”,when using this projector at highelevations (above 1400 m) only.LAMP POWERThis setting changes the lampbrightness. When set to “LOW”, theR G B / Y P B P R A U T O[R G B[Y P B P RV G A 6 0 / 5 2 5 P 5 2 5 P[V G A 6 0B A C K C O L O R B L U E[B L A C KF R O N T / R E A R F R O N T[R E A RD E S K / C E I L I N G D E S K[C E I L I N GL A M P P O W E R H I G H[L O WS X G A M O D E S X G A[S X G A +F A N C O N T R O L S T A N D A R D[H I G HOption settingsO P T I O N 1O S D O NA U T O S I G N A L O NA U T O K E Y S T N O NA U T O R G B I N O NR G B 2 S E L E C T I N P U TR G B / Y P B P R A U T OV G A 6 0 / 5 2 5 P 5 2 5 PS X G A M O D E S X G AB L A C K B O A R D O F FS E L E C T A D J R E T R NO P T I O N 2B A C K C O L O R B L U EF R O N T / R E A R F R O N TD E S K / C E I L I N G D E S KF A N C O N T R O L S T A N D A R DL A M P P O W E R H I G HL A M P R U N T I M E 1 0 0 HF U N C 1 I N D E XC O N T R O L K E Y O NA U T O P O W . O F F D I S A B L ES E L E C T A D J R E T R N