Panasonic Palmcorder PV-GS320 Operating Instructions Manual

Also see for Palmcorder PV-GS320: Brochure & specs Operating instructions

Contents

Panasonic Palmcorder PV-GS320 Operating Instructions Manual Manual pdf 69 page image

Others69LSQT1091Before requesting repair(Problems and solutions)Power/Body1: The Camcorder power cannot be turned on.• Is the battery fully charged? Use a fullycharged battery.• The battery protection circuit may haveoperated. Attach the battery to the AC adaptorfor 5 to 10 seconds. If the Camcorder stillcannot be used, the battery is faulty.• Is the LCD monitor opened or the viewfinderextended?2: The Camcorder power is turned offautomatically.• If you set [POWER SAVE] to [5 MINUTES] anddo not operate the Camcorder for about5 continuous minutes, the power isautomatically turned off for tape protection andpower conservation. To resume recording, turnthe [OFF/ON] switch to [OFF]. Then turn it to[ON] again. (-29-) Also, if you set[POWER SAVE] to [OFF], the power does notautomatically turn off.3: The Camcorder power does not stay onlong enough.• Is the battery low? If the remaining batterypower indication is flashing or the message“LOW BATTERY” is displayed, the battery hasrun down. Charge the battery or attach a fullycharged battery. (-15-)• Has condensation occurred? When you carrythe Camcorder from a cold place into a warmplace, condensation may occur inside it. If so,the power is turned off automatically, disablingall operations except for taking cassettes out.Wait until the condensation indicationdisappears. (-72-)4: Battery runs down quickly.• Is the battery fully charged? Charge it with theAC adaptor. (-15-)• Are you using the battery in an extremely coldplace? The battery is affected by ambienttemperature. In cold places, the operating timeof the battery becomes shorter.• Has the battery worn out? The battery has alimited life. If the operating time is still too shorteven after the battery is fully charged,depending on the usage, the battery has wornout and can no longer be used.5: The Camcorder cannot be operated thoughpowered up.The Camcorder does not operate normally.• The Camcorder cannot be operated unless youopen the LCD monitor or extend the viewfinder.• Remove the cassette and the card and thenpress the [RESET] button. (-71-) If normalconditions are not restored yet, turn off thepower. Then, about 1 minute later, turn on thepower again. (Conducting the above operationwhen the access lamp is on may destroy thedata on the card.)6: The cassette cannot be removed.• Does the status indicator comes on whenopening the cassette cover? (-16-) Make surethat the battery and the AC adaptor areproperly connected. (-15-)• Is the battery in use discharged? Charge thebattery and remove the cassette.• Close the cassette cover completely and fullyopen it again. (-20-)7: No operation other than cassette removalcan be performed.• Has condensation occurred? Wait until thecondensation indication disappears. (-72-)8: The remote control does not function.• Has the button-type battery of the remotecontrol run out? Replace it with a new button-type battery. (-26-)• Is the setting on the remote control correct? Ifthe setting on the remote control is not inagreement with the [REMOTE] setting on theCamcorder, the remote control does notoperate. (-27-)Recording1: Recording does not start although power issupplied to the Camcorder and the cassetteis correctly inserted.• Is the accidental erasure prevention slider onthe cassette open? If it is open (set to [SAVE]),recording cannot be performed. (-20-)• Is the tape wound to the end? Insert a newcassette.• Is the recording mode set? When in theplayback mode, recording cannot beperformed. (-21-)• Has condensation occurred? No operationother than cassette removal can be performedwhen condensation occurs. Wait until thecondensation indication disappears. (-72-)• Is the cassette cover open? If the cover isopen, the Camcorder may not operatenormally. Close the cassette cover. (-20-)2: The screen has changed suddenly.• Has the demonstration started? In the TapeRecording mode, if you set [DEMO MODE] >>[ON] without inserting a cassette and a card,the demonstration starts. For normal use, setthis function to [OFF]. (-65-)≥Audio dubbing ≥The section of a taperecorded in LP mode≥The blank section of atape≥Sounds sent through theDV terminal