Q-See QC818 User Manual
Also see for QC-SERIES: User manualUser manualSetup guideQuick start guideUser manual
                                              | |
Contents
| 
64 65ADDING AND DELETING REMOTE DEVICESThe lower portion of the window shows all devices currently connected to your NVR. If all ofyour channels are occupied, you will need to delete one of the connected devices from thislist by selecting the check box next to it and clicking delete. Items with a gray “X” are directlyconnected to your NVR and may only be removed by physically disconnecting them from yoursystem.Clicking on the IP Search button will create a list of all remote devices that the NVR was ableto detect. You may limit this search to only IP cameras by selecting IPC in the Filter pull-down. Items being accessed by your NVR over the Internet will not appear in the list at the topof the window. They must be added manually (see below).If you have an available channel, you may add a device by selecting the check box nextto it and then clicking Add. Please note that the NVR will connect automatically only withdevices from compatible manufacturers (see Section 2.4 IP Cameras or Section A.2Specifications for a list of compatible manufacturers) using their default user names andpasswords. If these have been changed, you will need to use the Manual Add feature instead.Manual AddIf you have changed the default settings of any remote device which you wish to use withyour NVR, you will need to use the Manual Add button at the bottom of the window toadd this device to the list of connected devices. This applies to cameras and DVRs whichwere previously connected but later removed from the list of connected items. Items beingaccessed from outside your local network will also need to be added using this button.Within the Manual Add window, some information may already be displayed but it may not becorrect for the device you are intending to connect.PICTURE 4-30REMOTE DEVICEFilter NoneDelete Manual AddIP Search AddOK Cancel4 IP Address Port Device ID Manufacturer Type1 10.1.1.65 Port 1 YZC2OC061966 Private IPC2 10.1.1.67 Port 2 YZCAU192012 Private IPC3 10.1.1.68 Port 4 TC2FW25600095 Private IPC4 196.219.8.50 4000 Privatechannel Edit Delete Status IP Address Port Device ID1 196.610.6.46 377772 10.1.1.67 Port 2 YZCAU1920123 10.1.1.68 Port 4 TC2FW256000954 10.1.1.65 Port 1 YZC2OC061966Device AddedManual AddChannelManufacturerIP AddressTCP PortUserPasswordRemote ChannelDecoder Buffer1PrivateIPC.myq-see.com37777admin1280Save CancelChannel - Select an available channel towhich you want to assign this device.Manufacturer - You can leave thisunchanged.IP Address - If this device is connected tothe same network as the NVR, the IP addresswill appear in upper portion of the RemoteDevice window along with the device name.If this device is located outside of your localnetwork, you will need to determine theIP address locally to the device (see theRemote Monitoring Guide).TCP Port - The default is 3777. Devicesbeing accessed over the Internet maybe using a different port. You will havedetermined this during setup.User/Password - Enter the user name and password you set for the device. The default username and password for QC-Series IP cameras are admin and admin. For other brands,please consult your product manual.Remote Channel - Leave this unchanged.Decoder Buffer - Ranges from 80 to 480, but it is better to leave it at the default value of 280.PICTURE 4-31PICTURE 4-32PICTURE 4-334.6 ADVANCEDThe settings in this menu cover user accounts, hard disk management, video display, andsystem maintenance.HDD MANAGEThis displays some of the same information found in the HDD Info window in the Info menu(see Section 4.2) but this window allows you to make additional settings.HDD MANAGESATA 1 2- -HDD No.TypeStatusCapacityRecord Time1 Set to Read/WriteOKAlarm SetExecuteHDD SettingAlarm Release HDD ChannelHDD Channel1511CancelSavechannel HDD Group2611channel HDD Group3711channel HDD Group4811channel HDD GroupMain Stream Ext Stream Snap PictureThe drive name and status is displayed.The status indicators are:Clicking on Alarm Set opens the Abnormality window which is covered immediatelyfollowing this section.Alarm Release – this turns off any disk alarm that may be occurring.HDD Setting - When you have multiple drives installed, you can designate which drive is theprimary and which is secondary. Multiple drives may be assigned to the same groupwhich means that the NVR will continue writing onto the next drive in the group afterthe first one is filled before going back and overwriting old records on the first.O Drive is operating normally.X Indicates an error- Hard drive not installed? Hard drive is damagedHDD Channel - If you have more than onehard drive installed in your NVR, youcan determine which drive video andstill images are recorded on. ClickingHDD Channel will open a newwindow with three tabs: Main Stream,Extra Stream (the lower bandwidthvideo used for remote monitoring)and Snap Picture (the still imagescaptured with the Snapshot function.Within each tab, you can set thedestination for each channels’ output. |
Related manuals for Q-See QC-SERIES
manualsdatabase
Your AI-powered manual search engine