QSC touchmix-30 pro User Manual

Also see for touchmix-30 pro: Quick start guide Technical notes User manual User manual Windows driver manual

Contents

QSC touchmix-30 pro User Manual Manual pdf 51 page image

431001108-01-AOutput ChannelsOutput Channel − OverviewProvides a single-screen view of frequently used controlsand indicators for the output channel.1. Overview tab – Selects the Channel Overview screen.2. Preset – Shows the currently selected Preset for thischannel. .3. Pick-off point – (Auxes only) Determines wherethe signal for the output channel is taken.4. Delay – Controls and indicates the amount of delay(up to 100 msec.) applied to the signal.5. Delay In – Applies / bypasses the delay.6. Reset – Sets all controls for the input channel to thefactory default position.7. Description of the Current Preset8. DCA – Indicates which DCA groups are assigned tothe channel.9. Mute – Indicates which Mute groups control thechannel.10. Parametric EQ Nraph – A graphic representationof the equalization curve based on the EQ settings.When the EQ is engaged, the trace becomes brighter.• EQ Nraph Vertical Scale – Represents audiolevel from -20 dB to +20 dB.• EQ Nraph Horizontal Scale – Representsfrequency from 20 Hz to 20 kHz.11. EQ Out/In – Engages / disengages the equalizer for the channel.12. EQ Handles – Touch, hold, and drag to change the Frequency and Gain of the associated EQ band. The frequency band button must be engagedto see the EQ Handles.13. Aux Sends –• Aux sends 9 – 14 are available for Aux Outputs 1 – 8 only,• Displays the system numbers and user-defined names for the Aux channels.• Adjustable sliders send signal to the associated Aux channel output.• Mute indicates if the channel’s send to an Aux is muted or not.14. Low and High Cut Filter and Frequency Bands 1, 2, 3, and 4 – These buttons engage or disengage the associated filter.To adjust the following parameters, select the field then use the Master encoder or the up/down nudge buttons on a mobile device.15. Nain, Bands 1, 2, 3, and 4 – Displays and adjusts gain (-15 to +15 dB) for the selected frequency band.16. Low and High Cut Filter Frequency – Displays and adjusts the knee frequency for the high and low cut filters.17. Frequency Bands 1–4 frequency adjustment fields – Displays and adjusts the center frequency for the four parametric EQ bands.NOTE!: The following section can be a Compressor or Limiter depending on the Comp/Limit switch on the Comp/Limiter tab.18. Comp –• Comp – Engages or disengages the channel’s compressor.• Threshold – Displays and sets the level at which compression begins.• Attack – Displays and sets the rate at which the compressor reaches its maximum compression when the threshold level is exceeded.• Release – Displays and sets the rate at which the compressor ceases gain reduction when signal drops below threshold.• Ratio – Displays and sets the amount of compression applied to the signal.HomeSelect anOutputBankSelectChannelSelectOverviewTab∞345 612Inputs 1-8CueAux1105u5102004010MainL/R105u5102004010Anti-FeedbackLimiter(Comp) Auxes Presets SetupPEQCompThresholdAttackReleaseRatioMMMMMM91011121314Aux 9Aux 10Aux 11Aux 12Aux 13Aux 14AUX SendsGEQGRLR1 23 45 67 8DefaultE10 Monitor MainCueMain MixL/RScene:ResetInJoe’s EarsAux 1Aux 2Aux 2Aux 3Aux 3Aux 4Aux 4Aux 5Aux 5Aux 6Aux 6Aux 7Aux 7Aux 8Aux 8Aux 9Aux 9Aux 10Aux 10Aux 11Aux 11Aux 12Aux 12Aux 13Aux 13Aux 14Aux 1420100-10-2020K10K5K2K1K5002001005020Hz3 4210.00 0.00 0.00 0.00120 80.0 400 2.0k 6.0k 8.0k20100-10-20PEQTuned for QSC E10 Monitor 1 2 3 4 5 6 7 8DCA 1 2 3 4 5 6 7 8Mute GroupsPreset E10 Monitor Pre Fdr Post Fdr Delayms0.00-12.016.050.04.0OverviewMuteMuteAux 1 OverviewPre Dyn Pre AllOut InCAFLFAux Out 1-82 316857 9411101416 1715131812Prev Next21435 6