Ravelli Francesca User And Maintenance Manual

Also see for Francesca: Installation manual

Contents

Ravelli Francesca User And Maintenance Manual Manual pdf 12 page image

User and maintenance manual for stoves with RDS technologyPag.1201/02/2016User and maintenance manual for stoves with RDS technology Pag.811/11/146.2 Environment of useThe positioning of the stove is decisive for successful even heating of the room. Before deciding where to place the stove, the following must betaken into account:- The stove must be installed on a floor with a sufficient carrying capacity. If the existing building does not meet this requisite, appropriate measuresmust be taken (i.e. load distribution plate).- The combustion air cannot be obtained from a garage or from an area without ventilation or exchange of air, but from a free or external space- The stove must not be installed in a bedroom, bathroom or shower, or where there is already another heating appliance without an autonomousair flow (chimney, stove etc.)- A minimum of 3” inches from the rear of the stove, 3” inches from the side of the stove and 16” inches from the top of the stove must be maintainedfrom combustible materials.- A non-combustable Hearth board 6” from front of unit and 6” from the sides must be installed before unit is placed on the floor.- Installation is better in a large and central room in the house to ensure maximum circulation of the heat;- Connection to the main supply is recommended using a grounded outlet (if the cable supplied is not long enough to reach the nearest outlet, usean extension cord with a surge protector);- The stove must be placed in a position that receives the necessary level of air for appropriate combustion of the pellets (at least 131.23 f3 /h mustbe available), in accordance with installation regulation and local legislations;- All joints for connector pipe is required to be fastened with at least three screws.- If vented horizontally joint should be siliconed with hi-temp. silicone and screwed so they are gas tight. (RTU 500 silicone)- the chimney connector shall not pass through an attic or roof space, closet or similar conceald space, or a floor or ceiling. Where passage througha wal, or partition of combustible construction is desired, the installationshall conform to CAN/CSA-B365.The stove must be installed and assembled by qualified personnel.The room must be:- Prepared for the environmental functioning conditions- Prepared with an adequate system of evacuation of smoke- Have a 120V 60 Hz (EN73-23) electricity mains supply- Do not connect this unit to a chimney flue serving another appliance- Use only UL Listed Type L Vent or Pellet Vent 3” in. I.D. venting system to exhaust. Do not install flue damper in the exhaust system of this unit.- The chimney connector and each other adjoining section must be firmly attached and secured to the stove.6.3 Mobile Home Requirements- Outside air is required- The heater must be secured to the floor using lag bolts.- The heater must be grounded to the chassis of the mobile home.- Installation should be in accordance with the manufactured home.- When outside air is required, system parts, such as vent sections, supports, spark arresters, rodent screens, etc. must be used.- The space heater is to be connected to a factory built chimney conforming to CAN/ULC-S629.- It is important to use all the specified components, do not use other components.- Installation shall maintain an effective vapour barrier at the location where the chimney or other component penetrates to the exterior of thestructure.-Operating the space heater with open firing doors can cause serious injuries and health damages due to excaping flames or carbon monoxidegeneration inside the room.- Adequate ventilation is required to avoid air starvation and icing which can determine an unhealthy indoor environment.- Do not overfire.- If the space heater is not correctly installed and operated it can interfere with smoke detectors.A Minimum 4’ clearance below or beside any door or window that opensMinimum 1’ clearance below or beside any window that does not open.B Minimum 1’ clearance above any door or window that opensC Minimum 2’ clearance from any adjacent buildingD Minimum 7’ clearance above any grade when adjacent to public walkwaysE Minimum 2’ clearance above any grass, plants, or other combustible materialsF Minimum 3’ clearance from any forced air intake of any other applianceG Minimum 2’ clearance below eaves or overhangsH Minimum 1’ clearance horizontally from combustible wallX Must be a minimum of 2’ above the roofWARNING: Do not install in bedroomCAUTION: The structural integrity of the mobile home floor,ceiling, walls, roof must be maintained.Refer to HUD Requirements, CFR 3280, Part 24NOTE: Install vent at clearances specified by the ventmanufactures.NOTE: Measure clearances to the nearest edge of the exhausthood.NOTE: Vent may not terminate in covered walkway or breezeway.NOTE: If venting horizontally, check your venting specifications fordistance pipe should extrude from building.6.2 Environment of useThe positioning of the stove is decisive for a successfuland equal heating of the room. Before deciding where to place the stove, the following must betaken into account:- The stove must be installed on a floor with a sufficient carrying capacity. If the existing building does not meet this requisite, appropriate measures mustbe taken (i.e. load distribution plate).- The combustion air cannot be obtained from a garage or from an area without ventilation or exchange of air, but from a free or external space- The stove must not be installed in a bedroom, bathroom or shower, or where there is already another heating appliance without an autonomous air flow(chimney, stove etc.)- A non-combustable Hearth board 6” from front of unit and 6” from the sides must be installed before unit is placed on the floor.- Installation is better in a large and central room in the house to ensure maximum circulation of the heat;- Connection to the main supply is recommended using a grounded outlet (if the cable supplied is not long enough to reach the nearest outlet, use anextension cord with a surge protector);- The stove must be placed in a position that receives the necessary level of air for appropriate combustion of the pellets (at least 131.23 f3/h must beavailable), in accordance with installation regulation and local legislations;- All joints for connector pipe is required to be fastened with at least three screws.- If vented horizontally joint should be siliconed with hi-temp. silicone and screwed so they are gas tight. (RTU 500 silicone)- the chimney connector shall not pass through an attic or roof space, closet or similar conceald space, or a floor or ceiling. Where passage through awal, or partition of combustible construction is desired, the installationshall conform to CAN/CSA-B365.The stove must be installed and assembled by qualified personnel.The room must be:- Prepared for the environmental functioning conditions- Prepared with an adequate system of evacuation of smoke- Have a 120V 60 Hz electricity mains supply- Do not connect this unit to a chimney flue serving another appliance- Use only UL Listed Type L Vent or Pellet Vent 3” in. I.D. venting system to exhaust. Do not install flue damper in the exhaust system of this unit.- The chimney connector and each other adjoining section must be firmly attached and secured to the stove.6.3 Mobile Home Requirements- Outside air is required- The heater must be secured to the floor using lag bolts.- The heater must be grounded to the chassis of the mobile home.- Installation should be in accordance with the manufactured home.- When outside air is required, system parts, such as vent sections, supports, spark arresters, rodent screens, etc. must be used.- The space heater is to be connected to a factory built chimney conforming to CAN/ULC-S629.- It is important to use all the specified components, do not use other components.- Installation shall maintain an effective vapour barrier at the location where the chimney or other component penetrates to the exterior of the structure.-Operating the space heater with open firing doors can cause serious injuries and health damages due to excaping flames or carbon monoxide generationinside the room.- Adequate ventilation is required to avoid air starvation and icing which can determine an unhealthy indoor environment.- Do not overfire.- If the space heater is not correctly installed and operated it can interfere with smoke detectors.A Minimum 4’ clearance below or beside any door or window that opens( with ooutside air insttalled, 1’ below or beside)Minimum 1’ clearance below or beside any window that does not open.B Minimum 1’ clearance above any door or window that opensC Minimum 2’ clearance from any adjacent buildingD Minimum 7’ clearance above any grade when adjacent to public walkwaysE Minimum 2’ clearance above any grass, plants, or other combustible materialsF Minimum 3’ clearance from any forced air intake of any other applianceG Minimum 2’ clearance below eaves or overhangsH Minimum 1’ clearance horizontally from combustible wallX Must be a minimum of 2’ above the roofWARNING: Do not install in bedroomCAUTION: The structural integrity of the mobile home floor,ceiling, walls, roof must be maintained.Refer to HUD Requirements, CFR 3280, Part 24NOTE: Install vent at clearances specified by the ventmanufactures.NOTE: Measure clearances to the nearest edge of the exhausthood.NOTE: Vent may not terminate in covered walkway or breezeway.NOTE: If venting horizontally, check your venting specificationsfor distance pipe should extrude from building.