Ravelli Francesca User And Maintenance Manual

Also see for Francesca: Installation manual

Contents

Ravelli Francesca User And Maintenance Manual Manual pdf 31 page image

User and maintenance manual for stoves with RDS technologyPag.3101/02/2016FLOWMETER (onlyif the RDS system isprovided)PHASE SCREWALARMTRIAC SCREWALARMNO FLOW (only ifthe RDS system isprovided)• The device is disconnected or defective •Please contact the local Technical Assistance Centre• The gear motor is not correctly connected •Please contact the local Technical Assistance Centre•The device in the motherboard which commands the feeding screwis defective• Please contact the local Technical Assistance Centre- The flow meter does not measure inlet air flow - Check if the ash pan and door are closed correctly and check if theair inlet pipe is obstructed.- If the problem persists, contact the Support Service9. Description of alarmsWARNING REASON SOLUTIONNO PELLET• The pellet hopper is empty • Check whether there are pellets in the hopper• The gearmotor does not load pellets. • Empty the hopper to check that no objects have fallen insidewhich could prevent the correct functioning of the screw• No pellet loading • Regulate the pellet setting• If the problem continues, contact the area TechnicalAssistance Centre.BLACK - OUT• No electricity supply during working phase • Press the off button and repeat switching on the stove• If the problem continues, contact the area Technical Assistance Centre.NO IGNITIONALARM• The pellet hopper is empty. • Check if there are pellets inside the hopper.• Setting of pellets and of intake during ignition phaseinsufficient. • Contact local Technical Assistance Centre.• The igniter is defective of not in correct position. • Contact local Technical Assistance Centre.ALARM LOWFLAME• The pellet hopper is empty. • Ceckis pellet is in the hopper• Bad setting of pellet and air for the ignition phase • Contact local Technical Assistance CentreALARM FANRPM• The speed of flue fan is lower more then 15% of set value. • Contact local Technical Assistance CentreALARM FANBROKEN• Flue fan encoder is not working or not correctly connected • Contact local Technical Assistance Centre.• No power supply to flue fan • Contact local Technical Assistance Centre.• The flue fan is blocked • Contact local Technical Assistance Centre.DEPRESSIONALARM• The combustion chamber is dirty • Follow the cleaning operations of the stove in the booklet• The chimney is blocked • Check that the chimney is clear and clean• The pressure switch is malfunctioning • Please contact local Technical Assistance CentreTHERMALALARM WITHRESET• The thermostat with manual reset has intervened • Reset the thermostat pressing the button on the backof the stove (see Pic. below).• The air fan is defective • Please contact local Technical Assistance Centre.• Combustion in the fire pot is notoptimal• Switch off the stove, clean the fire pot and regulatecombustion with the setting of the pellets.• If the problem continues, contact the area Technical Assistance Centre.HOT SMOKEALARM• Combustion in the fire pot is notoptimal• Switch off the stove, clean the fire pot and regulatecombustion with the setting of the pellets.• The air fan is defective • Contact local Technical Assistance Centre.• If the problem continues, contact the area Technical Assistance Centre.SMOKE SENSORALARMThe smoke sensor is malfunctioning • Please contact the local Technical Assistance CentreThe smoke sensor has been disconnected from the board • Please contact the local Technical Assistance CentreREASON SOLUTION• The door and the ash box are not closed correctly •Make sure they are properly closed.• Poor combustion in grate.•Switch off the stove, clean the fire pot and check the cleanliness ofthesupport bench, clean the tube bundle by activating the turbolators.andadjust the combustion through Pellet/Air settings.• Presence of foreign body in air intake tube. • Check for any foreign body and remove it• The air flow meter may be dirty. • Clean the flow meter with the stove in “Switched off” state• Contact the Support ServiceSIGNALLINGDo CLEANING Fire pot(only if the RDS system isprovided)1 - By pressing the button OK on the display. the alarm can be reset.3 - Try and repeat lighting after the cooling phase.2 - Unscrew the protection cap and pressthe button to reset the thermostat alarm.THERMAL ALARM WITH RESET