Raymarine p70 Installation And Operation Instructions Manual

Also see for P70: User reference Installation instructions Installation & operation instructions Installation guide Quick reference

Contents

Raymarine p70 Installation And Operation Instructions Manual Manual pdf 48 page image

8.5 Using the set-up wizardThe set-up wizard guides you through the steps for settingimportant preferences, such as preferred language and correctvessel type.The set up wizard contains 3 steps: language selection, vesseltype and welcome screen. When powering the p70 / p70r forthe first time in an unconfigured system, this set-up wizard isdisplayed automatically, and the first 3 steps listed below willnot be required.With the pilot in Standby mode:1. Select Menu.2. Select Set-up.3. Select Set-up wizard.4. Select the required language.5. Select the required vessel type.The welcome screen will now be displayed and your choiceshave been saved.6. Select OK to complete the set-up wizard.Vessel hull type selectionThe vessel hull type options are designed to provide optimumsteering performance for typical vessels.It is important to complete the vessel hull type selection as partof the initial set-up wizard, as it forms a key part of the autopilotcalibration process. You can also access the options at anytime with the pilot in Standby by selecting MENU > Set-up >Autopilot Calibration > Vessel Settings > Vessel Hull Type.As a general guide, select the option that most closely matchesyour vessel type and steering characteristics. The options are:• Race Sail.• Sail Cruiser.• Catamaran.• Workboat.• RIB.• Outboard Speedboat• Inboard Speedboat• Power Cruiser 1 (<12 kts)• Power Cruiser 2 (<30 kts)• Power Cruiser 3 (>30 kts)• Sport Fishing• Pro FishingIt is important to be aware that steering forces (and thereforerate-of-turn) vary significantly depending on the combination ofvessel type, steering system, and drive type. Therefore, theavailable vessel hull type options are provided for guidanceonly. You may wish to experiment with the different vessel hulltype options, as it might be possible to improve the steeringperformance of your vessel by selecting a different vessel type.When choosing a suitable vessel type, the emphasis should beon safe and dependable steering response.Important: If you change the vessel type after completing theDockside calibration process (using the Dockside wizard), allcommissioning settings will be reset to default settings, andyou will need to complete the Dockside calibration processagain.8.6 Dockside calibrationThe dockside calibration process must be completed beforeyour SPX autopilot system can be used for the first time. TheDockside wizard guides you through the steps required fordockside calibration.The Dockside wizard contains different steps depending onwhether you have a rudder reference transducer fitted to yourvessel:The following Dockside wizardprocedures only apply to vesselswithout a rudder referencetransducer:• Drive Type selection.• Rudder Limit setting.• Rudder Drive check.The following Dockside wizardprocedures only apply to vesselswith a rudder reference transducer:• Drive Type selection.• Align Rudder (rudder alignment).• Rudder Limit setting.• Rudder Drive check.On older SeaTalk SmartPilot systems the Dockside wizard isnamed Dealer Settings. Please refer to 8.7 Dealer settings forcalibration details.Using the Dockside wizardTo access the dockside wizard follow the steps below:Ensure the pilot is in Standby.1. Select Menu.2. Select Set-up.3. Select Autopilot Calibration.4. Select Commissioning.5. Select Dockside Wizard.6. Follow the on-screen instructions.Note: You can cancel the Dockside wizard at any time bypressing the Standby button.Selecting a drive typeDrive Type selection is available when the pilot is in standby,from either the Dockside wizard, or from the Vessel setting menu:MENU > Set-up > Autopilot Calibration > Vessel Settings .With the Drive Type menu displayed:1. Select your drive type.Note: If your drive type is not listed, contact your Raymarinedealer for advice.Checking the rudder alignment (AlignRudder)This procedure establishes port and starboard rudder limits forsystems using a rudder reference transducer.The rudder check forms part of the dockside calibration process.Thefollowingprocedureonlyappliesto vessels with a rudder referencetransducer.1. Center the rudder and select OK.2. When prompted, turn the rudder hard to port and select OK.3. When prompted, turn the rudder hard to starboard and selectOK.4. When prompted, turn the rudder back to the center andselect OK.Note: You can cancel Dockside calibration at any time byselecting STANDBY.48 p70 / p70R