Regency LIBERTY L900-LP Owners & Installation Manual

Contents

Regency ® L900 Direct Vent Gas Fireplace 39OPERATIONOPERATINGINSTRUCTIONS1) Read and understand these instructionsbefore operating this appliance.2) Check to see that all wiring is correct andenclosed to prevent possible shock.3) Check to ensure there are no gas leaks.4) Make sure the glass in the door frame isproperly positioned. Never operate theappliance with the glass removed.5) Verify that the venting and cap areunobstructed.6) Ensure that the brick panels are installed.7) Verify log placement. If the pilot cannot beseen when lighting the unit, the logs havebeen incorrectly positioned.8) The unit should never be turned off, and onagain without a minimum of a 60 secondwait.IMPORTANT Gas on/off knob cannot beturned from "PILOT" to "OFF" unless it ispartially depressed.Ensure that the 3 way switch on the manualcontrol panel is in the "Remote" position.The manual control panel is located on the lefthand side of the firebox behind the left sideexterior brick panel.During the first few fires, a white fi lmmay develop on the glass front as part ofthe curing process. The glass should becleaned after the unit has cooled downor the film will bake on and become verydifficult to remove. Use a non-abrasivecleaner and DO NOT ATTEMPT TO CLEANTHE GLASS WHILE IT IS HOT.Only when the pilot holds, without pressurebeing applied to the control knob, resecure theglass door to the unit. The unit must not beoperated with the glass door removed.IMPORTANTTo ignite or reignite the pilot, youmust first remove the glass door.LIGHTINGPROCEDUREThe FIRST FIRE in your heater is part of the paintcuring process. To ensure the paint is properlycured, it is recommended you burn your fireplacefor at least four (4) hours the first time.When first operated, the unit will release anodour caused by the curing of the paint and theburning off of any oils remaining from manufac-turing. Smoke detectors in the house may go offat this time. Open a few windows to ventilatethe room for a couple of hours. The glass mayrequire cleaning.NOTE: The main burner will always start on"HIGH" and resume it's last setting after20 seconds of operation.NOTE: When the glass is cold and the applianceis lit, it may cause condensation and fogthe glass. This condensation is normaland will disappear in a few minutes asthe glass heats up.DO NOT ATTEMPT TO CLEAN THEGLASS WHILE IT IS STILL HOT!FIRST FIREDO NOT BURN THE APPLIANCEWITHOUT THE GLASS FRONT INPLACE.3-way SwitchMATCHING REMOTEHANDSET & CONTROLBOX ID CODEThe Remote Control Handset has a set ofunique ID codes that is pre-programmed into itsmemory. This set of ID codes helps to differenti-ate one Remote Control Handset from anotherso that only the control box with a matching IDcode will respond to the appropriate RemoteControl Handset.To ensure the remote control is matched tothe receiver correctly, please follow the stepsbelow:1. Ensure that the Remote Control and the3-way switch located at the appliance areboth in the OFF position.2. Ensure that the pilot is lit and the pilotcontrol knob is in the ON position on theappliance.3. Install the 2 x AAA alkaline batteries into theRemote Control.4. Unplug and re-plug the power cord. Thepower cord is located on the left hand sideof the appliance and will be plugged into thereceptacle.5. Switch the 3-way switch located on the ap-pliance to the REMOTE position.6. Press and hold the PROG and FAN buttonssimultaneously for up to 20 seconds. Duringthis time, the remote will display LC while itis transmitting codes to the receiver. Onceit is successfully transmitted, one will hearthe solenoid click and the burners will comeon. If is does not work the first time, repeatsteps 1 - 6.7. Release both the PROG and FAN buttons.The remote will revert back to normal, butthe burner will still be on.8. Press the ON/OFF button on the remotecontrol 2 times to turn the burner off.9. The remote control is now programmed tothe receiver and the appliance can now beoperated with it.The control box will only learn the Remote IDcodes during the first 30 seconds after poweris applied and will ignore this special commandfrom the Remote after the first 30 seconds.NOTE: This must only be performed by a quali-fied installer.OPERATING INSTRUCTIONS