Regency ® P121/P121LC/P121RC/P131 Zero Clearance Room Sealed Gas Fireplace30OPERATING INSTRUCTIONSOPERATINGINSTRUCTIONS1) Read and understand these instructionsbefore operating this appliance.2) Check to see that all wiring is correct andenclosed to prevent possible shock.3) Check to ensure there are no gas leaks.4) Make sure the glass in the door frame isproperly positioned. Never operate the ap-pliance with the glass removed.5) Verify that the flueing and cap are unob-structed.6) Ensure that the brick panels are installed.7) Verify log placement. If the pilot cannot beseen when lighting the unit, the logs havebeen incorrectly positioned.8) The unit should never be turned off, and onagain without a minimum of a 60 secondwait.LIGHTINGPROCEDURE1) Push in gas control knob slightly and turn to“PILOT” position.2) Push in control knob all the way and hold inuntil the pilot lights up. Continue to hold thecontrol knob in for about 20 seconds afterthe pilot is lit. Release knob.3) Push in gas control knob slightly andturn to "ON" position.4) Turn ON the flame switch.SHUTDOWNPROCEDURE1) Turn OFF the flame switch.2) Push in gas control knob slightly and turn to"OFF" position.FIRST FIREDO NOT BURN THE APPLIANCEWITHOUT THE GLASS FRONT INPLACE.The first fire in your stove is part of the paint cur-ing process. To ensure that the paint is properlycured, it is recommended that you burn yourfireplace for at least four (4) hours the first timebefore you use it with the fan on.When first operated, the unit will release an odourcaused by the curing of the paint, the burningoff of any oils remaining from manufacturing.Smoke detectors in the house may go off at thistime. Open a few windows to ventilate the roomfor a couple of hours.Note: When the glass is cold and the appli-ance is lit, it may cause condensationand fog the glass. This condensationis normal and will disappear in a fewminutes as the glass heats up.During the fi rst few fi res, a white fi lm maydevelop on the glass front as part of thecuring process. The glass should be cleanedafter the unit has cooled down or the fi lmwill bake on and become very diffi cult toremove. Use a non-abrasive cleaner andDO NOT ATTEMPT TO CLEAN THE GLASSWHILE IT IS HOT.NORMAL OPERATINGSOUNDS OF GASAPPLIANCESIt is possible that you will hear some soundsfrom your gas appliance. This is perfectly normaldue to the fact that there are various gaugesand types of steel used within your appliance.Listed below are some examples. All are normaloperating sounds and should not be consideredas defects in your appliance.Blower:Regency® gas appliances use high tech blowersto push heated air farther into the room. It is notunusual for the fan to make a "whirring" soundwhen ON. This sound will increase or decreasein volume depending on the speed setting ofyour fan speed control.Burner Tray:The burner tray is positioned directly under theburner tube(s) and logs and is made of a differ-ent gauge material from the rest of the fireboxand body. Therefore, the varying thicknesses ofsteel will expand and contract at slightly differentrates which can cause "ticking" and "cracking"sounds. You should also be aware that as thereare temperature changes within the unit thesesounds will likely re-occur. Again, this is normalfor steel fireboxes.Blower Thermodisc:When this thermally activated switch turns ONit will create a small "clicking" sound. This is theswitch contacts closing and is normal.Pilot Flame:While the pilot flame is on it can make a veryslight "whisper" sound.Gas Control Valve:As the gas control valve turns ON and OFF, adull clicking sound may be audible, this is normaloperation of a gas regulator or valve.Unit Body/Firebox:Different types and thicknesses of steel willexpand and contract at different rates resultingin some "cracking" and "ticking" sounds will beheard throughout the cycling process.AERATIONADJUSTMENTThe burner aeration is factory set. Adjustmentmay be needed due to the local gas supply oraltitude. As a general rule if the flame is too yel-low open up the air shutter, if it is too blue closethe air shutter.NG 10mm openLPG 10mm openNOTE: This adjustment is only to be madeby an authorised person.Gas Inlet