Regency U32-NG5 Owners & Installation Manual

Also see for energy U32: Brochure & specs Specification sheet Owners & installation manual

Regency U32-NG5 Owners & Installation Manual Manual pdf 33 page image

U32-5 FPI Direct Vent Gas Insert 3333OPERATING INSTRUCTIONSCOPY OF LIGHTING INSTRUCTION PLATEsounds. You should also be aware that as thereare temperature changes within the unit thesesounds will likely re-occur. Again, this is normalfor steel fireboxes.Blower Thermodisc:When this thermally activated switch turns ONit will create a small "clicking" sound. This is theswitch contacts closing and is normal.Pilot Flame:While the pilot flame is on it can make a veryslight "whisper" sound.Gas Control Valve:As the gas control valve turns ON and OFF, adull clicking sound may be audible, this is normaloperation of a gas regulator or valve.Unit Body/Firebox:Different types and thicknesses of steel willexpand and contract at different rates resultingin some "cracking" and "ticking" sounds will beheard throughout the cycling process.MAINTENANCEINSTRUCTIONS1) Always turn the gas valve to off beforecleaning. For relighting, refer to lightinginstructions. Keep the burner and controlcompartment clean by brushing andvacuuming at least once a year. Whencleaning the logs, use a clean soft paintbrush as the logs are fragile and easilydamaged.2) Clean (never when unit is hot) appliance,door and louvers with a damp cloth. Neveruse an abrasive cleaner. The gold louvers(and optional gold door) may be scratchedif abrasives are used to clean them.The heater is finished in a heat resistantpaint and should only be refinished with heatresistant paint (not with wall paint). FPI usesStoveBrite Paint - Metallic Black #6309.3) Make a periodic check of burner for properposition and condition. Visually check theflame of the burner periodically, making surethe flames are steady; not lifting or floating.If there is a problem, call a qualified serviceperson.4) The appliance and venting system must beinspected before use, and at least annually,by a qualified field service person, to ensurethat the flow of combustion and ventilationair is not obstructed.During the annual service call, the burnersshould be removed from the burner trayand cleaned. Replace the embers but donot block the pilot.5) Keep the area near the appliance clear andfree from combustible materials, gasolineand other flammable vapours and liquids.6) Each time the appliance is lit, it may causecondensation and fog the glass. Thiscondensation and fog is normal and willdisappear in a few minutes as the glassheats up.Never operate the appliance without theglass properly secured in place or withthe door open.7) Do not use this appliance if any part has beenunder water. Immediately call a qualifiedservice technician to inspect the applianceand to replace nay part of the control systemand any gas control which has been underwater.8) Periodically check the pilot flames. Correctflame pattern has three strong blue flames: 1flowing around the thermopile and 1 aroundthe thermocouple, and 1 flowing across therear of the burner (it does not have to betouching the burner).1) Push in gas control knob slightly and turn to “PILOT” position.2) Push in control knob all the way and hold in untilthe pilot lightsup. Continue to hold the control knob in for about 20 secondsafter the pilot is lit. Release knob.3) Push in gas control knob slightly and turn to "ON" position.4) Turn ON the flame switch.2) Wait five (5) minutes to clear out any gas. If you then smell gasSTOP! follow “B” in the safety information above on this label. Ifyou don’t smell gas, go to the next step.3) Tu rn knob on gas control counterclockwise to “PILOT”.4) Pu sh in control knob all the way and hold in. Immediately pushblack button on spark igniter until pilot lights. Continue to hold thecontrol knob in for about 1/2 minute after the pilot is lit. Releaseknob and it will pop back up. Pilot should remain lit. If it goes out,repeat steps 3) and 4).If knob does not pop up when released, stop and immediately callyour service technician or gas supplier.If the pilot will not stay lit after several tries, turn the gas controlknob to “OFF” and call your service technician or gas supplier.5) Tu rn gas control knob counterclockwise to “ON”.6) Us e rocker switch to operate main burner.DO NOT REMOVE THIS INSTRUCTION PLATEFOR YOUR SAFETY READ BEFORE LIGHTINGA) This appliance has a pilot which must be lighted by hand, following the instructions below exactly.B) BE FORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier thanair and will settle on the floor.WHAT TO DO IF YOU SMELL GAS- Do not try to light any appliance- Do not touch any electric switch, do not use any phone in your building- Immediately call your gas supplier from a neighbors phone. Follow the gas supplier’s instructions.- If you cannot reach your gas supplier, call the fire department.C) Us try torepair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.D) Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance andto replace any part of the control system and any gas control which has been under water.E) Thisappliance needs fresh air for safe operation and must be installed so there are provisions adequate combustion + ventilation air.918-474bOFFWARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,or additional information consult a qualified installer, service agency or gas supplier.LIGHTING INSTRUCTIONSTO TURN OFF GAS APPLIANCETHERMOPILEELEMENTTHERMO-ELECTRIQUEPILOT BURNERVEILLEUSE1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. (Australia: A S5601-2004, New Zealand: NZS 5261)FOR UNITS NOT EQUIPPED WITH ELECTRIC SPARK:. Keep burnerappliance.STOP! Read the safety information above on this label.FOR ALL PROPANE UNITS ANDUNITS EQUIPPED WITH ELECTRIC SPARK BOXES:1) Push in gas control knob slightly and turn clockwise to“OFF”. Knob cannot be turned from “PILOT” to “OFF” unlessknob is pushed in slightly. Do not force.1) Turn off the flame switch.2) Push in the gas control knob slightly and turn clockwise to “OFF”. Do not force.3) Turn off all electric power to the appliance if service is to be performed.You may shut off the pilot during prolonged non use periods to conserve fuel.lWARNING: CHILDREN AND ADULTSSHOULD BE ALERTED TO THEHAZARDS OF HIGH SURFACETEMPERATURE AND SHOULD STAYAWAY TO AVOID BURNS OR CLOTHINGIGNITION. YOUNG CHILDREN SHOULDBE CAREFULLY SUPERVISED WHENTHEY ARE IN THE SAME ROOM ASTHE APPLIANCE.CAUTION: ANY SAFETY SCREEN ORGUARD REMOVED FOR SERVICING ANAPPLIANCEMUSTBEREPLACEDPRIORTO OPERATING THE APPLIANCE.CLOTHING OR OTHER FLAMMABLEMATERIAL SHOULD NOT BE PLACEDON OR NEAR THE APPLIANCE.