Regency U32-NG5 Owners & Installation Manual

Also see for energy U32: Brochure & specs Specification sheet Owners & installation manual

Regency U32-NG5 Owners & Installation Manual Manual pdf 9 page image

U32-5 FPI Direct Vent Gas Insert 9INSTALLATIONDMANUFACTUREDMOBILE HOMEADDITIONALREQUIREMENTS1) Ensure that structural members are not cutor weakened during installation.2) Ensure proper grounding using the #8ground lug provided.3) Appliance must be anchored to the floorwith the supplied anchoring methods.MATERIALS REQUIREDNo electrical power supply is required for the gascontrol to operate. A 120 Volt AC power cord ishooked up to the fan. Plug the 3 wire cord intoa suitable receptacle. Do not cut the groundterminal off under any circumstances. Whenconnected with 120 volts, the appliance mustbe electrically grounded in accordance withlocal codes, current version of CSA C22.1 (inCanada) or in the absence of local codes, with theNational Electrical Code ANSI/NFPA 70-1987.INSTALLATIONCHECKLISTBefore installing vent system ensure that the damperplate is open and secure to prevent the damper platefrom falling down and crushing the liner.The FPI Gas Insert is installed as listed.1) Check all clearances to combustibles, (Refer tosections "Minimum Fireplace Dimensions andClearances to Combustibles)2) Make the gas connection. (Refer to section"Gas Connection")3) Install the 3" flue liner to the sliding connectorplate. (Refer to section "Flue Liner Installation.")4) Slide the unit half way into the fireplace.5) Pull the vent connector plate through the taperedbrackets and fasten to the front plate. Refer tosection "Flue Liner Installation.")6) Slide the unit fully into the fireplace.7) Test gas pressure (Refer to section "Gas PipePressure Testing"). Check aeration system(Refer to section "Gas Insert Aeration System").8) Install standard and optional features. Referto the following sections:a. Brick Panelb. Log Setc. Faceplate & Trimd. Standard Flush Doore. Flush Trimf. Flush Louversg. Full Screen Doorsh. Wall Thermostati. Remote Control9) Final check: Before leaving this unit with thecustomer, the installer must ensure that theappliance is firing correctly. This includes:a) Clocking the appliance to ensure the correctfiring rate.b) Adjusting the primary air, if required, toensure that the flame does not carbon. See"Gas Insert Aeration System" section.c) Ensuring that the appliance is ventingcorrectly.MINIMUM FIREPLACEDIMENSIONSThe minimum fireplace clearances & dimensionsfor the FPI gas insert are shown in the followingdiagrams:Diagram 1Combustible Mantel Clearanceswith Flush Louvers in Masonryand Factory BuiltFireplace InstallationDiagram 2CLEARANCES TOCOMBUSTIBLESMinimum Clearances to CombustiblesFrom UnitSides A 10" / 255 mmCeiling B 47.5" / 1205 mmMantel C see Dia. 2 & 3Max. Mantle Depth G 12" / 305 mm(see Dia. 2)Min. Alcove Width K 48" / 1220 mmMax. Alcove Depth L 36" / 915 mm*No Hearth RequiredFaceplateFlushwithFloorCombustibleFlooringMantleC12" Max.GMax LentilBar DepthA HeightB DepthCWidth(rear)DWidth(front)ERegencyCountourFaceplate9" 22" 14" 22-1/2" 26-1/2"FullScreenDoors9" 22" 14" 22-1/2" 26-1/2"LowProfileFaceplate8-1/8" 22" 14" 22-1/1" 26-1/2"