Sanyo PLC-SP20N Owner's Manual Manual pdf 49 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Sanyo PLC-SP20N Owner's Manual

Also see for PLC-SP20N: Comparison chart

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 preview
Contents
  1. to the owner
  2. important safety instructions
  3. Table Of Contents
  4. INTRODUCTION
  5. POWER REQUIREMENT
  6. DESCRIPTION
  7. SETTING-UP THE PROJECTOR
  8. ADJUSTABLE FEET
  9. CONNECTING THE PROJECTOR
  10. Connecting an IBM-compatible desktop computer
  11. Connecting a Macintosh desktop computer
  12. Connecting an IBM-compatible laptop computer
  13. Connecting a Macintosh PowerBook computer
  14. CONNECTING THE VIDEO EQUIPMENT
  16. CONNECTING AN EXTERNAL SPEAKER
  17. OPERATION OF CONTROLS
  18. REAR OF THE PROJECTOR
  19. OPERATION OF REMOTE CONTROL
  20. REMOTE CONTROL BATTERY INSTALLATION
  21. CONTROL THE PROJECTOR
  22. MENU OPERATION
  24. USING THE PROJECTOR
  25. SOUND VOLUME ADJUSTMENT
  26. MODE SELECT
  27. SOUND ADJUSTMENT
  28. COLOR SYSTEM SELECT
  29. PICTURE IMAGE ADJUSTMENT
  30. PICTURE SCREEN ADJUSTMENT
  31. COMPUTER SYSTEM SELECT
  32. COMPATIBLE COMPUTER SPECIFICATION
  33. AUTO IMAGE FUNCTION
  35. PICTURE POSITION ADJUSTMENT
  36. PC ADJUSTMENT
  39. OTHER FUNCTION SETTING
  40. LAMP AGE
  41. AIR FILTER CARE AND CLEANING
  42. LAMP REPLACEMENT
  43. CLEANING THE LENS
  44. TROUBLESHOOTING
  45. TECHNICAL SPECIFICATIONS
Sanyo PLC-SP20N Owner's Manual Manual pdf 49 page image
– 49 –CLEANING THE LENSFollow these steps to clean the projection lens:1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.Avoid using an excessive amount of cleaner.Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.2. Lightly wipe the cleaning cloth over the lens.3. If you don’t intend to use the projector immediately, replace the lens cover.TROUBLESHOOTINGBefore calling your dealer or service station for assistance, follow these steps, to make sure everything is properly connected.1. Make sure you have connected the projector to your equipment as described in section “ CONNECTING THEPROJECTOR” on pages 10 ~ 17.2. Check cable connections. Verify that all computer, video and power cords are properly connected.3. Verify that power is switched on.4. If the projector still does not display an image, restart the computer.5. If the image still does not display, unplug the projector from the computer and check the computer monitor’s display.The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector,remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in thisorder: Projector, monitor, computer)6. If the problem still exists, check the following chart.¡Plug the projector into an AC outlet.¡Turn the MAIN ON/OFF button to ON.¡Press the LAMP POWER ON/OFF switch to ON.¡Be sure the READY INDICATOR light is ON.¡Wait one minute after the projector is turned OFF before turning the projectorback on.NOTE: After pressing the LAMP POWER ON/OFF button to OFF . The projectorfunctions as indicated.1. The LAMP POWER indicator will light and the READY indicator will turn off.2. After one minute, the READY indicator will light green again and the projectormay be turned on by pressing the LAMP POWER ON/OFF button.¡Check temperature warning indicator. If the indicator flashes red, the projectorcannot be turned on. (See “USING THE PROJECTOR” section on page 27).¡Check the projection lamp.¡Adjust the focus.¡Make sure the projection screen is at least 3.6 feet (1.1 m) from the projector.¡Check the projection lens to see if it needs cleaning.NOTE: Moving the projector from a cool temperature location to a warmtemperature location may result in moisture condensation on the lens. Insuch an event, leave the projector OFF and wait until condensationdisappears.Problem:No powerImage is out of focusTry these Solutions:
/ 52
Related manuals for Sanyo PLC-SP20N
Sanyo PLC-SU20N Owner's Manual first page preview
Sanyo PLC-SU20N Owner's Manual
Sanyo PLC-220N Owner's Manual first page preview
Sanyo PLC-220N Owner's Manual
Sanyo PLC-SP10N Owner's Manual first page preview
Sanyo PLC-SP10N Owner's Manual
Sanyo PLC-SP10N Owner's Manual first page preview
Sanyo PLC-SP10N Owner's Manual
Sanyo PLC-220N Owner's Manual first page preview
Sanyo PLC-220N Owner's Manual
Sanyo PLC-220N Owner's Manual first page preview
Sanyo PLC-220N Owner's Manual
Sanyo PLC-400N Owner's Manual first page preview
Sanyo PLC-400N Owner's Manual
Sanyo PLC-200N Owner's Manual first page preview
Sanyo PLC-200N Owner's Manual
Sanyo PLC-400N Owner's Manual first page preview
Sanyo PLC-400N Owner's Manual
Sanyo PLC-200N Owner's Manual first page preview
Sanyo PLC-200N Owner's Manual
This manual is suitable for:
PLC-SP20N
Manuals database logo
manualsdatabase
Your AI-powered manual search engine