Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- SPECIAL NOTICES
- PERSONAL PRECAUTIONS
- INTRODUCTION
- UNIT IDENTIFICATION
- CONTROLS, INDICATORS AND COMPONENTS
- Figure 4, AC Side
- Figure 5, Internal Components and Indicators
- Figure 7, DC Side
- INSTALLATION
- QUICK INSTALL
- COMPLETE INSTALL
- Figure 8, Air Flow Intake Location
- Figure 9, AC Input/Output Power Connection
- Figure 10, Warning Label
- Table 2, Minimum Recommended Battery Cable Size vs. Cable Length
- Table 3, Battery Cable To Maximum Breaker/Fuse Size
- Figure 11, Battery to Inverter Cable Connection
- Figure 12, Neutral-To-Ground Bond Switching: No External AC Source Connected
- Figure 13, Neutral-To-Ground Bond Switching: External AC Source Connected
- Figure 15, Multiple Point Ground System
- FUNCTIONAL TEST
- MENU SYSTEM
- USER MENU MAP
- SETUP MENU MAP
- USER MENU
- SETUP MENU
- OPERATION
- Figure 18, Trace™ SW Series Inverter Output Waveform
- POWER VS. EFFICIENCY
- INVERTER CAPACITY VS TEMPERATURE
- OPERATING MODES
- INVERTER MODE
- CHARGER MODE
- Figure 22, BTS (Battery Temperature Sensor)
- Table 4, Charging Setpoints For Common Battery Types
- INVERTER/CHARGER MODE
- GENERATOR SUPPORT MODE
- AUTOMATIC GENERATOR CONTROL MODE
- Figure 23, Two Wire Start Wiring Diagram
- Figure 24, Three Wire Start Wiring Diagram (HONDA Type)
- Figure 26, Relay RY7 and RY8 Sequence
- UTILITY BACKUP MODE
- UTILITY INTERACTIVE MODE
- Figure 28, Selling Power Stored In The Batteries; Hypothetical Time Of Day Operational History
- Figure 29, Utility Interactive Line-Tie System With Battery Backup Flow Diagram
- Figure 30, Overvoltage Protection for Battery
- ENERGY MANAGEMENT MODE
- PEAK LOAD SHAVING MODE
- LOW BATTERY TRANSFER (LBX) MODE
- USING MULTIPLE INVERTERS
- TECHNICAL INFORMATION
- BATTERY SIZING
- BATTERY BANK SIZING
- BATTERY CARE AND MAINTENANCE
- Table 7, Battery State of Charge Voltage
- BATTERY INSTALLATION
- BATTERY HOOK-UP CONFIGURATIONS
- Figure 33, Parallel Configuration: 12-Volt Battery Wiring
- Figure 34, Series-Parallel Configuration: 6-Volt Battery Wiring
- BATTERY CABLE INDUCTANCE
- APPLICATIONS
- TROUBLESHOOTING GUIDE
- INVERTER/CHARGER TERMINOLOGY
- Figure 36, AC Waveforms
- SPECIFICATIONS AND FEATURES (60 Hz Models)
- SPECIFICATIONS AND FEATURES (50 Hz Models)
- DIMENSIONS
- INSTALLATION DIAGRAMS
- Figure 39, Installation Diagram, 240 VAC, 3 Wire, Grid Connected, Generator Backup
- USER SETTINGS WORKSHEETS
- APPENDIX
- OTHER PRODUCTS
- REFERENCE TABLES AND GRAPHS
- Figure 40, AWG Wire Size
- Table 13, Recommended Minimum AC Wire Sizes (75 C)
- STORAGE CHECKLIST
- WARRANTY/REPAIR INFORMATION
- WARRANTY OR REPAIR SERVICE REQUIRED
- INDEX
|
MENU SYSTEM 2001 Xantrex Technology, Inc.5916 - 195th Street N. E.Arlington, WA 98223Telephone: 360/435-8826Fax: 360/435-2229www.traceengineering.comSW Series Inverter/ChargerPart No. 2031-5Rev. C: February 2001Page33MENU SYSTEMOVERVIEWThe operation of the inverter is determined by the settings in the menu system. The menu system isdivided into a USER MENU and a SETUP MENU. Each of the menu systems is divided into MENUHEADINGS and MENU ITEMS. The menu headings break the menu into groups of related menu items.At the Menu Item level a setting can be adjusted, a mode can be selected or information can be displayed.When a number is included with the graphic of the menu heading or menu item in this manual, the valuesshown are the default value and are for a 12-volt domestic (120VAC/60Hz) model SW SeriesInverter/Charger. For 24 volt systems multiply the DC settings shown by 2, for 48 volt systems multiply theDC settings shown by 4.• The USER MENU provides the controls and settings needed on a daily basis. It allows you to turn onthe inverter and generator, read the AC and DC meters, check on an error cause and even adjuststhe inverter’s time clock.• The SETUP MENU provides all of the settings required to configure the inverter to operate in thenecessary modes for your installation. They are separated from the USER MENU to reduce tamperingand simplify the daily operation of the inverter.The SW Series Inverter/Charger MENU SYSTEM is accessed through the CONTROL PANEL on the frontof the unit. To access the SETUP MENU, press both the red ON/OFF MENU and green GEN MENUbuttons at the same time once. The display will show INVERTER SETUP (9). This is simply thecontinuation of the same menu system of the USER MENU. If you select a menu heading less than nine,or press either the red or green buttons, you will have to re-enter the setup menu by pressing the red andgreen buttons at the same time again.
|
