Page 130FT-991 O PERA T I N G M A N U A L059 CW FREQ DISPLAYFunction: Sets the PITCH frequency offset.Available Values: DIRECT FREQ/PITCH OFFSETDefault Setting: PITCH OFFSETDescription: Sets the displayed frequency offset whenswitching the transceiver mode between SSB and CW.DIRECT FREQ:Displays the same frequency in CW mode as inSSB mode without any offset added.PITCH OFFSET:Displays the frequency in CW mode with thepitch offset added. When CW BFO is set to USB,the displayed frequency will be increased andwhen CW BFO is set to LSB, the displayed fre-quency will be decreased with pitch offset added.060 PC KEYINGFunction: Sets the RTTY/DATA jack for keying.Available Values: OFF/DAKY/RTS/DTRDefault Setting: OFFDescription:OFF:Disables keying from DATA PTT (pin 3) of theRTTY/DATA jack.DAKY:Controls the transmit from the RTTY/DATA jack(pin 3) on the rear panel.RTS:Controls the transmit from the USB virtual COM/RTS ports.DTR:Controls the transmit from the USB virtual COM/DTR ports.061 QSK DELAY TIMEFunction: Sets the time delay before transmitting thekeying signal.Available Values: 15/20/25/30msecDefault Setting: 15msecDescription: The delay time in QSK mode before trans-mitting the CW signal may be set in 5 msec steps.062 DATA MODEFunction: Selects the operating scheme in DATA mode.Available Values: PSK/OTHERSDefault Setting: PSKDescription: Selects the operating scheme (PSK orOTHERS) in DATA mode.063 PSK TONEFunction: Set the PSK tone.Available Values: 1000/1500/2000HzDefault Setting: 1000HzDescription: Selects the PSK tone frequency.064 OTHER DISP (SSB)Function: Sets the displayed frequency offset in DATAmode.Available Values: −3000 - 0 - 3000Hz (10Hz/step)Default: 0HzDescription: Sets the displayed frequency offset inDATA mode. The frequency can be set in steps of 10Hz.065 OTHER SHIFT (SSB)Function: Sets the carrier point in DATA mode.Available Values: −3000 - 0 - 3000Hz (10Hz/step)Default: 0HzDescription: Sets the carrier point in DATA mode. Thefrequency can be set in steps of 10 Hz.066 DATA LCUT FREQFunction: Sets the low-frequency cutoff audio filter inDATA mode.Available Values: OFF/100Hz - 1000Hz (50Hz/step)Default Setting: 300HzDescription: This is the low-frequency cutoff audio filterin DATA mode.The cutoff frequency can be set at 50 Hz incrementsbetween 100 Hz and 1000 Hz.067 DATA LCUT SLOPEFunction: Sets the slope of the low-frequency cutoff au-dio filter in DATA mode.Available Values: 6dB/oct / 18dB/octDefault Setting: 18dB/octDescription: Selects the slope setting of the low-fre-quency cutoff audio filter in DATA mode.068 DATA HCUT FREQFunction: Sets the high-frequency cutoff audio filter inDATA mode.Available Values: OFF/700Hz - 4000Hz (50Hz/step)Default Setting: 3000HzDescription: This is the high-frequency cutoff audio fil-ter in DATA mode.The cutoff frequency can be set at 50 Hz incrementsbetween 700 Hz and 4000 Hz.069 DATA HCUT SLOPEFunction: Sets the slope of the high-frequency cutoff au-dio filter in DATA mode.Available Values: 6dB/oct / 18dB/octDefault Setting: 18dB/octDescription: Selects the slope setting of the high-fre-quency cutoff audio filter in DATA mode.070 DATA IN SELECTFunction: Selects the input jack for DATA mode.Available Values: MIC/REARDefault Setting: REARDescription: Selects the input jack to be used in DATAmode.MIC:Inputs signals from the MIC jack on the frontpanel.REAR:Inputs signals from the USB jack or RTTY/DATA jack on the rear panel.M enu M oDe