Yamaha RX V365 - AV Receiver Owner's Manual

Contents

16 EnThe “BASIC SETUP” feature is a useful way to set upyour system quickly and with minimal effort.Notes• Make sure that you disconnect your headphones from this unit.• If you wish to configure this unit manually using more preciseadjustments, use the detailed parameters in “SOUND MENU” (seepage 32).• Altering any parameters in “BASIC SETUP” resets all parametersmanually adjusted in “SOUND MENU” (see page 32).• Initial settings are indicated by (*) in the following each parameters.• Press nRETURN on the remote control to return to the previous menulevel.1 Press hAMP on the remote control.2 Press kMENU.“BASIC SETUP” appears on the front panel display.3 Press lENTER to enter “BASIC SETUP.”“ROOM: S M L” appears on the front panel display.4 Press ll / h to select the desired setting.Select the size of the room where you have installedyour speakers. The room sizes are defined as follows:5 Press ln to select “SUBWOOFER” and thenll / h to select the desired setting.“SUBWOOFER” and the current setting appear onthe front panel display.6 Press ln to select “SPEAKERS” and thenll / h to select the number of speakersconnected to this unit.“SPEAKERS” and the current setting appear on thefront panel display.7 Press ln to select “SET” and then ll / hto select the desired settings.“SET” and “CANCEL” appear on the front paneldisplay.y• You can also press kMENU to cancel the setup procedure.8 Press lENTER to confirm your selection.If you selected “SET” in step 7, each speaker outputsa test tone twice in turn. “CHECK:TestTone” appearson the front panel display for a few seconds and then“CHECK OK?” appears on the front panel display.y• Check the speaker connections (see page 9) and adjust the“SPEAKERS” settings back in step 6, if necessary.• The indicator of the speaker currently outputting the test toneflashes on the front panel display.9 Press ll / h to select the desired settings.10 Press lENTER to confirm your selection.• If you selected “YES” in step 9, the setupprocedure is completed and then display returns tothe top set menu display. Press kMENU to exitfrom “BASIC SETUP.”• If you selected “NO” in step 9, the front speakerlevel adjustment display appears on the front paneldisplay.11 Press lk / n to select a speaker and thenll / h to adjust the balance.The selected speaker and the front left speaker (or thesurround left speaker) output a test tone in turn.• Press lh to increase the value.• Press ll to decrease the value.■ The balance between speakers you canadjust in each item is defined as follows.Note• The available speaker channels differ depending on the setting of thespeakers.12 Press kMENU to exit from “BASIC SETUP.”Basic setupChoice Approximate Size of the roomS 16 x 13 ft, 200 ft 2 (4.8 x 4.0 m, 20 m2)M* 20 x 16 ft, 300 ft 2 (6.3 x 5.0 m, 30 m2)L 26 x 19 ft, 450 ft 2 (7.9 x 5.8 m, 45 m2)Choice ConditionYES* When you have a subwoofer in your system.NONE When you do not have a subwoofer in yoursystem.Choice Display Speakers2spk Front L/R3spk Front L/R Center4spk Front L/R, Surround L/R5spk* Front L/R, Center, Surround L/RL RL C RL RSL SRL C RSL SRChoice FunctionSET Applies the settings you made.CANCEL* Cancels the setup procedure without makingany changes.Choice FunctionYES* Completes the setup procedure if the test tonelevels from each speaker were satisfactory.NO Proceeds to the speaker level adjustment menuto balance the output level of each speaker.Choice Adjusted balance between speakersFR the front left and right speakersC the front left and center speakersSL the front left and surround left speakersSR the surround left and surround right speakersSWFR the front left speaker and the subwoofer