Yamaha RX V365 - AV Receiver Owner's Manual

Contents

33 EnSet menuEnglishINTRODUCTIONADDITIONALINFORMATION APPENDIXPREPARATIONBASICOPERATIONADVANCEDOPERATIONLFE signals outputLow-frequency signals outputNotes*1 Outputs the low-frequency signals of the front channels and otherspeakers to “SML” or “NONE.”*2 Always output the low-frequency signals of the front channels.*3 Output the low-frequency signals if the sizes of speakers are set to“LARGE” (or “LRG”).*4 Output the low-frequency signals of the speakers set to “SML.”■ Crossover CROSSOVERUse this feature to select a crossover frequency of all thespeakers set to “SML” (or “SMALL”) or to “NONE” in“SPEAKER SET” (see pages 31 and 32).Choices: 40Hz, 60Hz, 80Hz*, 90Hz, 100Hz, 110Hz,120Hz, 160Hz, 200HzNote• All frequencies below the selected frequency will be sent to thesubwoofer or to the speakers set to “LRG” (or “LARGE”) in “SPEAKERSET” (see pages 31 and 32).■ Subwoofer phase SWFR PHASEUse this feature to switch the phase of your subwoofer ifbass sounds are lacking or unclear.Use this feature to manually adjust the output level of eachspeaker.Control range: –10 to 0* to +10 dBControl step: 1 dBNotes• The available speaker channels differ depending on the setting of thespeakers.• This does not affect recorded material.Use this feature to manually adjust the distance of eachspeaker and the delay applied to the respective channel.All sounds would be adjusted to arrive at the listeningposition at the same time regardless of distance from eachspeaker.■ Unit UNIT■ Speaker distancesControl range: 0.30 to 24.00 m (1.0 to 80.0 ft)Control step: 0.10 m (0.5 ft)Initial setting:FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)CENTER: 2.60 m (8.5 ft)SUR. L/SUR. R: 2.40 m (8.0 ft)Note• The available speaker channels differ depending on the setting of thespeakers.Use this feature to adjust the built-in 5-frequency band(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphicequalizer for the center channel so that the tonal quality ofthe center speaker matches that of the front speakers.Control range: –6.0 to 0* to +6.0 dBControl step: 0.5 dBy• Press lk / n to select a frequency band and ll / h to adjust theselected frequency band.• You can make adjustment while listening to the currently source or a testtone.Following is an example where “100Hz” is selected as thefrequency band.Choice Subwoofer Front speakers Other speakersBOTH* Output No output No outputSWFR Output No output No outputFRONT No output Output No outputChoice Subwoofer Front speakers Other speakersBOTH* *1 *2 *3SWFR *4 *3 *3FRONT No output *1 *3Choice FunctionNRM* Does not reverse the phase of your subwoofer.REV Sets the phase of your subwoofer to reverse.Speaker level B)SP LEVELSP LEVEL Adjusted speakerFL Front left speakerFR Front right speakerC Center speakerSL Surround left speakerSR Surround right speakerSWFR SubwooferSpeaker distance C)SP DISTANCEChoice Conditionmeters When you adjust speaker distances in meters.feet* When you adjust speaker distances in feet.SP DISTANCE Adjusted speakerFRONT L Front left speakerFRONT R Front right speakerCENTER Center speakerSUR. L Surround left speakerSUR. R Surround right speakerSWFR SubwooferCenter graphic equalizer D)CENTER GEQ100Hz--||-- 0