GET TO KNOW THE REMOTE CONTROL: MBR 3457PROGRAMMING YOUR REMOTEIf yt,u are using Zenith products, the remote is programmed for the most commonly used codes. For other audio/video brands youwill have to program the remote.Follow these steps for each product you are using: NOTES:To program the remote:1. Locate the three-digit code for your brand (such as Zenith) andequipment (such as VCR) in the code table.2. Press and hold PRG with a small blunt object until the indicatorlights (about three seconds).3. Press TV, VCR, CABLE or AUX to select the product youwant your remote to control. (Use CABLE or AUX toprogram your remote for a second TV or VCR or toprogram your remote for a video disc player or audioequipment.)4. Enter the three-digit code then press ENTER. The indicator lightshould flash then turn offto indicate that the code was accepted. Ifthe light stays on, repeat steps 3 and 4 or try using a different code.5. Write the codes that operate your equipment on the labelinside the battery compartment for future reference.UI To erase all code programming and return to the factorypreset codes, enter code 9-1-1 when programming theremote.If no key on your remote is pressed within 60 seconds, theprogramming process will stop, and you will have to startagain.I:::1 You may cancel programming at any time by pressing PRG.SPECIAL FEATURESAUX+I, AUX+2, AUX+3 CAPABILITYYour remote can control up to seven electronic components, ifyou have programmed the remote for four components using theTV, VCR, CABLE and AUX keys, you may also program it forup to three additional components.To program AUX+I, AUX+2, & AUX+3:1. Locate the three-digit code for your equipment in the code table.2. Press and hold PRG until the indicator lights.3. Press AUX and "'1" simultaneously to select AUX+I.4. Enter the three-digit code then press ENTER. The indicator lightshould flash then turn off to indicate that the code was accepted. Ifthe light stays on, repeat steps 3 and 4 or try using a different code.5. Repeat steps 2 -- 4 for AUX+2 and AUX+3 programming.6. Write the codes that operate your equipment on the label; inside the battery compartment for future reference.Once programmed, hold down the AUX key and press 1, 2 or 3,to access the additional AUX +1, 2 or 3 mode.CABLE BOX VOLUMEYou may use your remote to control cable box volume and mut-ing if available on your equipment.I12 To program the cable box volume: IProgramyour cable box code into the CABLE or the AUX mode.I'i Repeat the pn_gramming steps, again using the CABLE or AUX Ikey. hutenter code 3-9-.-9inste',dof a brand c_xleand press IENTER. !NOTE:F..l To restore TV volume/mute control to the CABLE or AUXmode, reprogram your cable code into that mode.AMPLIFIER VOLUME OVERRIDEYou may use your remote to override your TV, VCR or videodisk player's volume functions with your amplifier's volume andmuting.To program the amplifier volume override:1. Program your amplifier code into the CABLE or one of theAUX modes.2. Select the mode on your remote O'V, VCR, etc.) where youwant the amplifier volume control function to appear. In otherwords, if you want to operate the volume and mute of youramplifier while the remote is in TV mode, press TV for this step.3. Enter code 4-9-9, followed by ENTER.The amplifier volume and mute features are now available in theTV mode.NOTES:I.J To restore normal volume and muting control to your TVcable box, reprogram the remote for these units into eachmode (TV, VCR, etc.) to be restored.I::l CD and tape devices will automatically select amplifier vol-ume and mute......... 3_4