hager TRM691AU Manual
LEDIn1 In2L3,5max10ATRM691AU200 W AC1 230 V 50Hz433.5 Mhz 10mW 45°CTRM691AU200 W AC1 230 V 50Hz433.5 Mhz 10mW 45°Ccfg fctLED LzRadio transmitter/receiver2 inputs + 1 dimmer 200WLoad type230 V Incandescent lamps 10 ... 200 W230 V halogen lamps 10 ... 200 W230 V Halogen ELV (12 or 24 V) via ferromagnetic transformer 10 ... 175 VA230 V Halogen ELV (12 or 24V) via electronic transformer 10 ... 175 VALED 230 V Dimmable LEDs 3 ... 50 WTechnical characteristicsSupply voltage 230 V +10 %-15% 50 Hz240 V +6%/-6% 50 HzProduct consumption 100mWUpstream protection:circuit breaker 10ATransmission frequency/Emission power433,05 - 434,79 MHz10 mWDimensions 40 x 40 x 18 mmMax. connectiondistance per input < 10 mMinimum contactsclosing time 50 msDegree of protection IP 20Operating altitude ≤ 2000 mPollution degree 2Overvoltage category IIIOperating temperature -15 °C —> + 45 °CStorage temperature - 20°C —> + 70 °CReceiver category 2 / Transmitter duty cycle<10%Electric connection: 0,5 mm2 —> 1,5 mm20,5 mm2 —> 2,5 mm2- This unit is to be installed by a qualifiedprofessional only according to theinstallation standard in force in the country.- Cut off 230V power supply to the productbefore connection of or operation on theinputs.- Do not remove the insulating sleeves onthe unused input wires.The TRM691AU is a radio transmitter/receiver,powered in series with the load. It is used fordimming incandescent, LV and ULV halogen, anddimmable LED loads.It includes:- 2 inputs for connection of pushbuttons, switchesor other automatic control contacts.- A dimming output (max. 200W ).The inputs connected to the product are freelyprogrammable. They can control the local outputor other outputs.quicklink products can be configured togetherand operated within the same radio installation.Caption1 Pushbutton or switch2 Connecting wires of the 2 inputs for a switch orpushbutton3 Pushbutton and feature LED T of output4 Pushbutton and configuration LED R5 Connector block :- L : Phase 230 V- : Dimming output 230 VODo not cut the input wires, even if they are notused.Features• 1 independent channel controlled by radio.(output 200W AC1 230V).• 2 inputs for contact free of potential.In operation :• Availability of output manual control bypushbutton T• Display of output state on LED fct (red light ON= active output).The specific features of each product depend onconfiguration and set-up.Learning the load typeThe first time it is turned on, the product undertakesautomatic learning of the connected lamp type.A brief flicker may be observed during this phase(duration 2 to 3 s) after which the lamp type isstored in the product.After a power outage or change of lamp, thedimmer starts a new detection.If the user notices unsatisfactory operation, thesetting can be edited manually.Manual setting of the loadMake 5 consecutive short presses on the dimmerpushbutton, until the lamp is observed to flash.6LE005076DThe dimmer is now in manual setting mode.Briefly press the dimmer pushbutton to select thedesired setting: (see table below)Note: Automatic departure from manual mode andsetting validation occur after 10 s inactivity.DimmingpushbuttonNumber of shortpressesNumber ofblinks Setting type1x 1xAutomaticdetection mode(default value)2x 2x Standard LEDmode3xThe lamp is lit at the minimumlevel = minimum threshold settingmode active.Further presses of the dimmingpushbutton are used to test otherlevels (to perform the test in thedark).Saving of the minimum thresholdafter 10 s inactivityProtection against overheating and overloadThe product is automatically protected againstoverloads, short circuits and overheating. In theevent of overheating or overload, the availablepower is automatically reduced.Factory set-upBy default, input 1 is configured to receive apushbutton and to control the local dimmingoutput (short press = ON/OFF; maintained push= increase/decrease with the direction changingfollowing each new press).This link can be edited or deleted in configurationmode.OA factory reset of the product reinstalls this link(factory settings). Input 2 is not pre-programmed.Factory ResetMaintain R pushbutton down until LED cfgflickers (>10s), then release. cfg LED turns OFF tosignal Factory Reset end. This operation removesthe entire product configuration in any configurationmode.After power switch-On or Factory Reset, wait for15s before to do a new configuration.OThese instructions for use form an integral partof the product and must be retained by the enduser.6LE005076D1TRM691AUNon-dimmable LED and compact fluorescent lamps are not compatible with this product.Metal surfaces in the direct vicinity of theproduct (e.g. flush mounted metal boxes)may reduce the radio range.Avoid the use of a metal front plate forswitches in combination with flush mountedmetal boxes.Complies withIMDA StandardsDA101847 |
Related manuals for hager TRM691AU
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine