Genie Z-135/70 manuals
Z-135/70
Table of contents
- October
- safety rules
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Hydraulic Oil Specifications
- Hydraulic Component Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Repair Procedures
- about this section
- Platform Controls
- Platform Circuit Board
- How to Remove the LED Circuit Board
- How to Reset a Proportional Valve Coil Default
- How to Set the Function Thresholds and Default Functions Speeds
- How to Adjust the Function Speeds
- How to Adjust the Function Ramp Rate Setting
- Platform Components
- Platform Rotator
- How to Bleed the Platform Rotator
- Platform Overload System (if equipped)
- Platform Overload Recovery Message
- Jib Boom Components
- Jib Boom Cable Track
- How to Repair the Cable Track
- Jib Boom
- Jib Boom Lift Cylinder
- Jib Boom Level Cylinder
- Jib Boom Extension Cylinder
- Boom Components
- Primary Boom Cable Track
- How to Repair the Primary Boom Cable Track
- Secondary Boom Cable Track
- How to Repair the Secondary Boom Cable Track
- Primary Boom
- Primary Boom Lift Cylinder
- Secondary Boom Lift Cylinder
- Primary Boom Extension Cylinder
- Secondary Boom Extension Cylinders
- Engines
- How to Install the Flex Plate
- Ground Controls
- How to Use the Recovery Mode
- Circuit Boards
- Membrane Decal
- Full Machine Calibration
- Display Module
- Hydraulic Pumps
- How to Prime the Function Pump
- How to Adjust the Function Pump Pressure Compensator
- Drive Pump
- How to Prime the Drive Pump
- Manifolds
- Valve Adjustments - Function Manifold
- Platform Manifold
- Jib Boom Manifold
- Function Enable Valve
- Turntable Rotation Manifold
- Steer and Axle Manifold
- Valve Adjustments - Steer and Axle Manifold
- Traction Manifold Components
- Valve Adjustments - Traction Manifold
- Valve Coils
- Turntable Rotation Components
- How to Adjust the Turntable Rotation Gear Backlash
- Turntable Level Sensor - How to Calibrate the Turntable Level Sensor
- Axle Components
- How to Calibrate a Replacement Steer Sensor
- Steer Cylinders
- Axle Extension Cylinders
- Section 4 Fault Codes
- fault codes
- Deutz TD 2.9 L4 Engine Fault Codes
- Perkins 854F-34T Engine Fault Code
- Section 5 Schematics
- Wire Circuit Legend
- Wire Color Legend
- Limit Switches and Angle Sensors
- Circuit Connector Legend
- Drive Chassis and Platform Controller Pin Legend
- Safety Controller Pin Legend
- Turntable Controller Pin Legend
- Telematics Connector Pin Legend
- Engine Relay and Fuse Panel Legend - Deutz TD2011L04i
- Engine Relay and Fuse Panel Legend - Deutz TD2.9
- Engine Relay and Fuse Panel Legend - Perkins 1104D-44T
- Engine Relay and Fuse Panel Legend - Perkins 854F-34T
- Electrical Symbols Legend
- Hydraulic Symbols Legend
- Perkins 854F-34T Engine Electrical Schematic
- Perkins 854F-34T Engine Harness
- Deutz TD2.9 Engine Electrical Schematic
- Deutz TD2.9 Engine Harness
- Hydraulic Generator (Welder Option)
- Generator Wiring Schematic
- Hydraulic Schematic (to SN ZX13516H-2804)
- Hydraulic Schematic (from SN ZX13516H-2805)
- Electrical Schematic
Z-135/70
Table of contents
Z-135/70
Table of contents
manualsdatabase
Your AI-powered manual search engine