Acewell ACE-HG20 User Manual

Acewell ACE-HG20 User Manual Manual pdf 1 page image

ATV/Snowmobile/Motorcycle/Scooter Heated GripsACE-HG20/21/21T User ManualThanks for purchasing our heated grips. For smooth installation, we recommend you read the guide carefully andfollow the steps below. During installation, please be careful not to damage the wiring or pull wire out of theterminals in the multipin plugs. If you have any doubts about the installation then please contact your grips supplierfor advice or arrange for professional installation.Plug and play adaptor cables have been developed for some vehicle. Check with your grip supplier which they canoffer.There are three versions of the grips as follows:ACE-HG20 (Motorcycle/ Scooter): 7/8” handlebars with twist grip throttleACE-HG21 (ATV/Snowmobile/PWC): 7/8” handlebars with thumb throttleACE-HG21T: 7/8” handlebars with thumb throttle including a thumb warmer** PLEASE NOTE THE FOLLOWING SAFETY INFORMATION **• DO NOT HOLD THE GRIPS WITH BARE HANDS! ALWAYS WEAR GLOVES TO AVOID BURNS!• SWITCHING THE GRIPS ON FOR MORE THAN A FEW SECONDS IF NOT FITTED TO THEHANDLEBARS WILL CAUSE DAMAGE TO THE GRIPS AND MAY WARP THE INNER TUBE• THE CONTROL BUTTON IS AN ELECTRONIC MICROSWITCH AND ONLY REQUIRES A GENTLEPRESS. PLEASE DO NOT TRY TO PULL THE BUTTON OUT TO CLEAN IT, DOING SO WILLDESTROY THE SILICONE AND IT WILL NOT BE POSSIBLE TO REINSTALL THE BUTTON.COMPONENTS 1 × Left Grip with temperature controller button. 1 × Right grip. 1 × Thumb warmer kit (ACE-HG21T only) 1 × Connecting wire or bike specific plug and play cable. 2 × Cable tie 2 × Bar-end capFEATURES! ACEWELL grips fit any 7/8” / 22mm handlebars to work with existing twist grip throttle tubes (ACE-HG20) orthumb throttle (ACE-HG21).! Push button temperature controller and power level display built into left grip allows an easy installation and noneed for additional switches.! 5 levels of grip heat temperature with fast-heat at power on.! 5 color illumination of the control button to indicate selected temperature.! The integrated control/display module keeps the original look of the bike but still allows full functionality of thegrips.! Classic slimline design which suits all types of motorcycle, scooter, ATV, PWC and Snowmobile.! Optional thumb heat pad available.! Hard wearing and anti-slip silicone outer layer giving soft but durable texture.! Low voltage detection - the grips automatically switch off to help protect against a flat battery! Simple installation with minimal wiring and detailed fitting instructions.INSTALLATION & WIRINGACE-HG20 & HG-211. Use the appropriate tool to remove the existing grips.Clean the handlebars and throttle tube as applicable with solvent and ensure the bars are free of residue and glue.2. Slide the Right grip onto throttle sleeve (HG20) or handlebar (HG21) and then the Left grip onto the handlebar.Apply Epoxy into the handlebar or throttle sleeve to hold the grips securely in place.Align the grips so that the cables point downwards and the control switch (button) can be easily pressed with yourthumb3. Connect the plug and play cable or the power tails to the left grip. If using the power tails then the black wireshould connect to negative (battery -) and red wire to positive (+12v)The grips feature an automatic power off function to save your battery so they can be connected to either anignition live or directly to the battery depending on your preference4. Connect the Right twist throttle grip to the Left grip.5. After installation, swing the handlebar left to right to ensure nothing obstructs the movement.ACE-HG21TFollow steps 1-3 above4. The HG21T includes a thumb warmer.5. Use solvent to clean the thumb throttle, remove the backing paper from the heater and stick to the thumb throttleusing the self-adhesive pad.6. Cover the heat pad with the supplied heat shrink tubing, and shrink into place using a hot air gun or flame.7. Plug the thumb heater inline between the left and right grips8. After installation, swing the handlebar left to right to ensure nothing obstructs the movements.

/ 2

Related manuals for Acewell ACE-HG20