Canon PIXMA MX700 series Quick Start Manual

Also see for PIXMA MX700 Series: Supplementary guide Brochure & specs Cleaning guide Network Setup Guide Quick start guide

An Error Message Is Displayed on the LCDIf an error message is displayed on the LCD, take the corresponding action described below.''The ink may have run out. Replacingthe ink tank is recommended."I U041"Print head is not installed. Install the. print head."U051"The type of print head is incorrect.Install the correct print head."U052"Some ink tanks are not installed inplace."U072"More than one ink tank of the followingcolor is installed."U071"The remaining level of the ink cannotbe correctly detected."U130"The following ink tank cannot berecognized."U043U140U150"The ink has run out. Replace the inktank."U163If the lamp on the ink tank is flashing, ink may have run out.Replacing the ink tank is recommended.If printing is in progress and you want to continue printing, press the OK buttonwith the ink tank installed. Then printing can continue. Replacing the ink tank isrecommended after the printing. The machine may be damaged if printing iscontinued under the ink out condition.See "Replacing an Ink Tank" on page 80.m NoteIf multiple ink lamps are flashing red, see "Getting the Ink Status Information" onpage 80 and check the status of each ink tank.Follow the directions given in your setup sheet to install the Print Head.If the Print Head is already installed, remove the Print Head once and thenreinstall it.If the error is not resolved, the Print Head may be damaged. Contact yourCanon service representative.Possible causes are as follows:• Some ink tanks are not installed in the correct position. (The lamp on the inktank flashes.)• More than one ink tanks of the same color are installed. (The lamp on the inktank flashes.)Confirm that the ink tanks are installed in the appropriate positions.See "Replacing an Ink Tank" on page 80., The remaining ink level cannot be correctly detected. (The lamp on the ink tankflashes.)Replace the ink tank and close the Scanning Unit (Printer Cover).Printing with an ink tank that was once empty may damage the machine.If you want to continue printing in this condition, you need to release the function, for detecting the remaining ink level. Press and hold the Stop/Reset button forat least 5 seconds, and then release it.With this operation, releasing the function for detecting the remaining ink level ismemorized. Please be advised that Canon shall not be liable for any machinemalfunction or damage caused by refilled ink tanks.See "Replacing an Ink Tank" on page 80.• The ink tank is not compatible with this machine. (The lamp on the ink tank isoff.)Install an appropriate ink tank.See "Replacing an Ink Tank" on page 80.• An Ink tank error has occurred. (The lamp on the ink tank is off.)Replace the ink tank.See "Replacing an Ink Tank" on page 80.Ink has run out. (The lamp on the ink tank flashes.)Replace the ink tank and close the Scanning Unit (Printer Cover).Printing under the current condition may damage the machine.If you want to continue printing in this condition, you need to release the functionfor detecting the remaining ink level. Press and hold the Stop/Reset button forat least 5 seconds, and then release it.With this operation, releasing the function for detecting the remaining ink level ismemorized. Please be advised that Canon shall not be liable for anymalfunction or trouble which may be caused by continuation of printing underthe ink out condition.See "Replacing an Ink Tank" on page 80.Troubleshooting 101An Error Message Is Displayed on the LCDIf an error message is displayed on the LCD, take the corresponding action described below.''The ink may have run out. Replacingthe ink tank is recommended."I U041"Print head is not installed. Install the. print head."U051"The type of print head is incorrect.Install the correct print head."U052"Some ink tanks are not installed inplace."U072"More than one ink tank of the followingcolor is installed."U071"The remaining level of the ink cannotbe correctly detected."U130"The following ink tank cannot berecognized."U043U140U150"The ink has run out. Replace the inktank."U163If the lamp on the ink tank is flashing, ink may have run out.Replacing the ink tank is recommended.If printing is in progress and you want to continue printing, press the OK buttonwith the ink tank installed. Then printing can continue. Replacing the ink tank isrecommended after the printing. The machine may be damaged if printing iscontinued under the ink out condition.See "Replacing an Ink Tank" on page 80.m NoteIf multiple ink lamps are flashing red, see "Getting the Ink Status Information" onpage 80 and check the status of each ink tank.Follow the directions given in your setup sheet to install the Print Head.If the Print Head is already installed, remove the Print Head once and thenreinstall it.If the error is not resolved, the Print Head may be damaged. Contact yourCanon service representative.Possible causes are as follows:• Some ink tanks are not installed in the correct position. (The lamp on the inktank flashes.)• More than one ink tanks of the same color are installed. (The lamp on the inktank flashes.)Confirm that the ink tanks are installed in the appropriate positions.See "Replacing an Ink Tank" on page 80., The remaining ink level cannot be correctly detected. (The lamp on the ink tankflashes.)Replace the ink tank and close the Scanning Unit (Printer Cover).Printing with an ink tank that was once empty may damage the machine.If you want to continue printing in this condition, you need to release the function, for detecting the remaining ink level. Press and hold the Stop/Reset button forat least 5 seconds, and then release it.With this operation, releasing the function for detecting the remaining ink level ismemorized. Please be advised that Canon shall not be liable for any machinemalfunction or damage caused by refilled ink tanks.See "Replacing an Ink Tank" on page 80.• The ink tank is not compatible with this machine. (The lamp on the ink tank isoff.)Install an appropriate ink tank.See "Replacing an Ink Tank" on page 80.• An Ink tank error has occurred. (The lamp on the ink tank is off.)Replace the ink tank.See "Replacing an Ink Tank" on page 80.Ink has run out. (The lamp on the ink tank flashes.)Replace the ink tank and close the Scanning Unit (Printer Cover).Printing under the current condition may damage the machine.If you want to continue printing in this condition, you need to release the functionfor detecting the remaining ink level. Press and hold the Stop/Reset button forat least 5 seconds, and then release it.With this operation, releasing the function for detecting the remaining ink level ismemorized. Please be advised that Canon shall not be liable for anymalfunction or trouble which may be caused by continuation of printing underthe ink out condition.See "Replacing an Ink Tank" on page 80.Troubleshooting 101