Chapter 1414-1014.3.8 SSSW-SW1414.3.8.1 List of Functions 0011-1751iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iT-14-1014.3.8.2 Detailed Discussions of Bit 2 0011-1752iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iUse it to specify whether to convert or not convert an inch-configuration resolution into a millimeter-configuration resolution for image read in G3 transmission:either in sub scanning direction only or in both main and sub scanning directions. The setting is valid only when bit 1 of SW05 of #SSSW is set to '1'.14.3.8.3 Detailed Discussions of Bit 4 0011-1753iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iUse it to specify whether to declare or not declare an inch-configuration resolution to the other machine for G3 communication: if 'declare' is selected, the machinewill indicate that it reads and records at an inch-configuration resolution using the DIS, DCS, or DTC signal.14.3.9 SSSW-SW2814.3.9.1 List of Functions 0011-1754iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iT-14-1114.3.9.2 Detailed Discussions of Bit 0 0011-1755iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to use the V.8 protocol when calling. If NO is selected, the V.8 protocol is inhibited at calling and the V.21 protocol is used.14.3.9.3 Detailed Discussions of Bit 1 0011-1756iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to use the V.8 protocol when called. If NO is selected, the V8 protocol is inhibited when called and the V.21 protocol is used.14.3.9.4 Detailed Discussions of Bit 2 0011-1757iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iIf ANSam signal is not received during transmission, select whether to use the V.8 protocol when the other fax machine declares the V.8 protocol in DIS signal. IfNO is selected, the CI signal is not transmitted and the V.8 protocol is not used even if the DIS that specifies the V.8 protocol is received.The V.8 late start is not executed during manual transmission regardless of this setting.14.3.9.5 Detailed Discussions of Bit 3 0011-1758iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether to declare the V.8 protocol in DIS signal for reception. If NO is selected, the V.8 protocol cannot be used because it is not declared in DIS signal.The V.8 late start is not executed during manual reception regardless of this setting.14.3.9.6 Detailed Discussions of Bit 4 0011-1759iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether the receiver falls back during V.34 reception. If 'Prohibit' is selected, the receiver does not fall back.14.3.9.7 Detailed Discussions of Bit 5 0011-1760iR2016J / iR2016 / iR2020 / / iR2016i / iR2020iSelect whether the transmitter falls beck during V.34 transmission. If 'Prohibit' is selected, teh transmitter does not fall back.Bit Function 1 00 not used - -1 not used - -2 direction of scanning for inch/mm conversion both main and subscanning directionssub scanningdirection only3 not used - -4 inch-configuration resolution declaration declare do not declare5 not used - -6 not used - -7 not used - -Bit Function 1 00 Caller V.8 protocol NO YES1 Called party V.8 protocol NO YES2 Caller V.8 protocol late start NO YES3 Called party V.8 protocol late start NO YES4 V.34 reception fallback Prohibited Not prohibited5 V.34 transmission fallback Prohibited Not prohibited6 not used - -7 not used - -
