Danfoss FC 300 Series Programming Manual

Also see for VLT AutomationDrive FC 301: Installation guide Operating guide Installation guide Design guide Installation guide

Contents

Danfoss FC 300 Series Programming Manual Manual pdf 70 page image

3.7 Parameters: 5-** Digital In/Out3.7.1 5-0* Digital I/O ModeParameters for configuring the input and output using NPNand PNP.These parameters cannot be adjusted while motor isrunning.5-00 Digital I/O ModeOption: Function:Digital inputs and programmed digital outputs are pre-programmable for operation either in PNP or NPNsystems.[0] * PNP Action on positive directional pulses (↕). PNP systemsare pulled down to GND.[1] NPN Action on negative directional pulses (↕). NPN systemsare pulled up to + 24 V, internally in the adjustablefrequency drive.NOTE!Once this parameter has been changed, it must be activatedby performing a power cycle.5-01 Terminal 27 ModeOption: Function:[0] * Input Defines terminal 27 as a digital input.[1] Output Defines terminal 27 as a digital output.5-02 Terminal 29 ModeOption: Function:[0] * Input Defines terminal 29 as a digital input.[1] Output Defines terminal 29 as a digital output.This parameter is available for FC 302 only.3.7.2 5-1* Digital InputsThe digital inputs are used for selecting various functions inthe adjustable frequency drive. All digital inputs can be setto the following functions:Digital input function Select TerminalNo operation [0] All *term 32, 33Reset [1] AllCoast inverse [2] All *term 27Coast and Reset Inverse [3] AllQuick stop inverse [4] AllDC brake inverse [5] AllStop inverse [6] AllStart [8] All *term 18Latched start [9] AllReverse [10] All *term 19Start reverse [11] AllEnable start forward [12] AllEnable start reverse [13] AllJog [14] All *term 29Preset reference on [15] AllPreset ref bit 0 [16] AllPreset ref bit 1 [17] AllPreset ref bit 2 [18] AllFreeze reference [19] AllFreeze output [20] AllSpeed up [21] AllSlow [22] AllSet-up select bit 0 [23] AllSet-up select bit 1 [24] AllPrecise stop inverse [26] 18, 19Precise start, stop [27] 18, 19Catch up [28] AllSlow-down [29] AllCounter input [30] 29, 33Pulse input Edge Trigged [31] 29, 33Pulse input Time Based [32] 29, 33Ramp bit 0 [34] AllRamp bit 1 [35] AllMains failure inverse [36] AllLatched precise start [40] 18, 19Latched precise stopinverse[41] 18, 19DigiPot Increase [55] AllDigiPot Decrease [56] AllDigiPot Clear [57] AllDigipot Hoist [58] AllCounter A (up) [60] 29, 33Counter A (down) [61] 29, 33Reset Counter A [62] AllCounter B (up) [63] 29, 33Counter B (down) [64] 29, 33Reset Counter B [65] AllMech. Brake Feedb. [70] AllMech. Brake Feedb. Inv. [71] AllPID Error Inv. [72] AllPID Reset I-part [73] AllPID enable [74] AllPTC Card 1 [80] AllFC 300 standard terminals are 18, 19, 27, 29, 32 and 33. MCB101 terminals are X30/2, X30/3 and X30/4.Terminal 29 functions as an output only in FC 302.Parameter Descriptions FC 300 Programming Guide3-48 MG.33.MA.22 - VLT® is a registered Danfoss trademark3