Type Designation P15K P18K P22K P30K P37K P45K P55K P75K P90KTypical Shaft Output [kW] 15 18.5 22 30 37 45 55 75 90IP20/Chassis B3 B3 B4 B4 B4 C3 C3 C4 C4IP21/Type 1 B1 B1 B2 B2 B2 C1 C1 C2 C2IP55/Type 12 B1 B1 B2 B2 B2 C1 C1 C2 C2IP66/NEMA 4X B1 B1 B2 B2 B2 C1 C1 C2 C2Output currentContinuous (3 x 525–550 V) [A] 23 28 36 43 54 65 87 105 137Intermittent (3 x 525–550 V) [A] 25 31 40 47 59 72 96 116 151Continuous (3x525–600 V) [A] 22 27 34 41 52 62 83 100 131Intermittent (3x525–600 V) [A] 24 30 37 45 57 68 91 110 144Continuous kVA (525 V AC) [kVA] 21.9 26.7 34.3 41 51.4 61.9 82.9 100 130.5Continuous kVA (575 V AC) [kVA] 21.9 26.9 33.9 40.8 51.8 61.7 82.7 99.6 130.5Max. input currentContinuous (3x525–600 V) [A] 20.9 25.4 32.7 39 49 59 78.9 95.3 124.3Intermittent (3x525–600 V) [A] 23 28 36 43 54 65 87 105 137Max. pre-fuses1) [A] 40 50 60 80 100 150 160 225 250Additional specificationsEstimated power loss at ratedmax. load [W] 4) 285 329 460 560 740 860 890 1020 1130Max. cable size (line power,motor, brake) [mm2]/(AWG) 2) - [35]/(2) [50]/(1) [955)]/(3/0)Efficiency 3) 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98Table 8.8 Line power supply 3x525–600 V AC - Normal overload 110% for 1 minute, P15K-P90K8.1.6 Line Power Supply 3 x 525–690 V ACType Designation P1K1 P1K5 P2K2 P3K0 P4K0 P5K5 P7K5Typical Shaft output (kW) 1.1 1.5 2.2 3.0 4.0 5.5 7.5IP20/ Chassis A3 A3 A3 A3 A3 A3 A3Output currentContinuous (3 x 525–550 V) [A] 2.1 2.7 3.9 4.9 6.1 9.0 11.0Intermittent (3 x 525–550 V) [A] 3.4 4.3 6.2 7.8 9.8 14.4 17.6Continuous (3x551–690 V) [A] 1.6 2.2 3.2 4.5 5.5 7.5 10.0Intermittent (3x551–690 V) [A] 2.6 3.5 5.1 7.2 8.8 12.0 16.0Continuous KVA 525 V AC 1.9 2.5 3.5 4.5 5.5 8.2 10.0Continuous KVA 690 V AC 1.9 2.6 3.8 5.4 6.6 9.0 12.0Max. input currentContinuous (3 x 525–550 V) [A] 1.9 2.4 3.5 4.4 5.5 8.1 9.9Intermittent (3 x 525–550 V) [A] 3.0 3.9 5.6 7.0 8.8 12.9 15.8Continuous (3x551–690 V) [A] 1.4 2.0 2.9 4.0 4.9 6.7 9.0Intermittent (3x551–690 V) [A] 2.3 3.2 4.6 6.5 7.9 10.8 14.4Additional specificationsMax. cable cross-section 5) for line power, motor, brakeand load sharing [mm2] ([AWG]) 4, 4, 4 (12, 12, 12) (min. 0.2 (24)Max. cable cross-section 5) for disconnect[mm2] ([AWG]) 6, 4, 4 (10, 12, 12)Estimated power loss at rated max. load (W) 4) 44 60 88 120 160 220 300Efficiency 3) 0.96 0.96 0.96 0.96 0.96 0.96 0.96Table 8.9 A3 Enclosure, Line Power Supply 3x525–690 V AC IP20/Protected Chassis, P1K1-P7K5Specifications VLT® AQUA Drive FC 20258 Danfoss A/S © 10/2014 All rights reserved. MG20MA2288