Denon ADV-700 Operating Instructions Manual
Also see for ADV-700: Brochure & specsOperating instructionsOperating instructionsOperating instructionsService manual
10ENGLISH9 REMOTE CONTROL UNIT• The included remote control unit (RC-901) can be used to operate not only this unit but other remote control compatibleDENON components as well. In addition, the memory contains the control signals for other remote control units, so it can beused to operate non-Denon remote control compatible products.(1) Inserting the batteriesq Remove the remote control unit’s rear cover.w Set three R6P/AA batteries in the battery compartment inthe indicated direction.e Put the rear cover back on.Notes on Batteries• Use R6P/AA batteries in the remote control unit.• The batteries should be replaced with new onesapproximately once a year, though this depends on thefrequency of usage.• Even if less than a year has passed, replace the batterieswith new ones if the set does not operate even when theremote control unit is operated nearby the set. (The includedbattery is only for verifying operation. Replace it with a newbattery as soon as possible.)• When inserting the batteries, be sure to do so in the properdirection, following the “≈” and “√” marks in the batterycompartment.• To prevent damage or leakage of battery fluid:• Do not use a new battery together with an old one.• Do not use two different types of batteries.• Do not short-circuit, disassemble, heat or dispose ofbatteries in flames.• Remove the batteries from the remote control unit whenyou do not plan to use it for an extended period of time.• If the battery fluid should leak, carefully wipe the fluid off theinside of the battery compartment and insert new batteries.• When replacing the batteries, have the new batteries readyand insert them as quickly as possible.(2) Using the remote control unit1c 8 1:02:46DVDTONEVOLUMEBANDMODEMENUFUNCTIONDISPLAYRETURN INPUT MODE SURROUNDTOP MENUSETUPSDB/TONEMUTESURR.PARASUB TITLEANGLEAUDIOSHIFTCH.SELECTCHT.TONETUPROG/DIRECT REPEAT A-BREPEATRANDOMDVDTV/VCRCHVOLSLEEPONOFFREMOCON MODE2345689071STATUSCDR/MD/TAPE TUNER/TV/VCRVCR POWERTV POWERTVVCRNTSC/PALENTERMUTEON23456CLEARCALL0MEMOPOWERCHCHCHOFF189+107°°Approx. 7m• Point the remote control unit at the remote sensor on themain unit as shown on the diagram.• The remote control unit can be used from a straight distanceof approximately 7 meters from the main unit, but thisdistance will be shorter if there are obstacles in the way orif the remote control unit is not pointed directly at theremote sensor.• The remote control unit can be operated at a horizontal angleof up to 30 degrees with respect to the remote sensor.NOTES:• It may be difficult to operate the remote control unit if theremote sensor is exposed to direct sunlight or strongartificial light.• Do not press buttons on the main unit and remote controlunit simultaneously. Doing so may result in malfunction.• Neon signs or other devices emitting pulse-type noisenearby may result in malfunction, so keep the set as faraway from such devices as possible.(3) Preset memory[1] Audio Component• The signals of your other Denon products can be stored in theincluded remote control unit’s preset memory to operateeither the CDR, MD or TAPE function.Operation is not possible for some models.[2] TV• Other makes of components can be operated by setting thepreset memory for your make of TV.This remote control unit can be used to operate componentsof other manufacturers without using the learning function byregistering the manufacturer of the components as shown onthe List of Preset Codes (attached sheet).Operation is not possible for some models.VOLUMEENTERBANDMODEMENU FUNCTIONDISPLAY RETURN INPUT MODE SURROUNDTOP MENUSETUPSDB/TONEMUTESURR.PARASUB TITLE ANGLEAUDIORTRDS CTPTYSHIFTCH.SELECTCHT.TONETUPROG/DIRECT REPEAT A-B REPEAT RANDOMDVDTV/VCRCHVOLSLEEPONOFFREMOCON MODE2 34 5 68 9CLEARCALL 0+1071STATUSCDR/MD/TAPE TUNER/TV/VCRVCR POWERVCR POWERTV POWERTV POWERTVVCRNTSC/PALMEMOPOWERPOWERCHCHCH11VOLUMEENTERBANDMODEMENU FUNCTIONDISPLAY RETURN INPUT MODE SURROUNDTOP MENUSETUPSDB/TONEMUTESURR.PARASUB TITLE ANGLEAUDIORTRDS CTPTYSHIFTCH.SELECTCHT.TONETUPROG/DIRECT REPEAT A-B REPEAT RANDOMDVDTV/VCRCHVOLSLEEPONOFFREMOCON MODE2 34 5 68 9CLEARCALL 0+1071STATUSCDR/MD/TAPE TUNER/TV/VCRVCR POWERVCR POWERTV POWERTV POWERTVVCRNTSC/PALMEMOPOWERPOWERCHCHCH1111 While pressing the CDR/MD/TAPE remote control modeselector button, input the 3-digit number (“000”, “111”and “222”) corresponding to the device you want topreset (CDR, MD or TAPE), referring to the table below.• Release the CDR/MD/TAPE button after inputtingthree digits. This completes the presetting operation.Table 1: Combinations of Personal System CodesInput the 3-digit number while pressingCDR/MD/TAPE.CDR/MD/TAPE01 1 12 2 20 0CDRMDTAPE✽ This is set to CDR by factory default.NOTE:• Only one device (CDR, MD or TAPE) can be stored in thepreset memory.1 Press the CALL button while pressing theTUNER/TV/VCR remote control mode selector button,then input the three-digit number corresponding to thecode of the manufacturer of the TV whose signals youwant to store, referring to the included list of remotecontrol unit codes.• Release the TUNER/TV/VCR button after inputtingthree digits. This completes the presetting operation.Example: To preset to “Hitachi 074”Press the buttons below while pressingTUNER/TV/VCR.TUNER/TV/VCRCALLTV POWERTV POWER0 7 4HITACHI“074”✽ This is set to “Hitachi 074” by factory default.NOTE:• Preset codes set upon shipment from the factory andwhen reset. |
Related manuals for Denon ADV-700
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine