MONITOR OUTS-VIDEO195ONRelationship between the video input signal and monitor output according to the VIDEOCONVERT MODE settings of MAIN ZONEVIDEO ✳3S-VIDEOS-VIDEOS-VIDEOS-VIDEOVideo convertEEVIDEOS-VIDEOS-VIDEOCOMPONENTCOMPONENTCOMPONENT ✳1COMPONENT ✳1S-VIDEOCOMPONENT ✳2COMPONENT ✳2S-VIDEOCOMPONENT ✳2COMPONENT ✳2COMPONENTEEEEEEEECC (1080p)CC (480i/576i)Input signalsS-VIDEO VIDEOEE EEEE CCCC EECC CCEE EECC (480p ~ 720p) EE EEEE EEHDMIEEEEEEEEEEEEEECOMPONENTEEVIDEOS-VIDEOS-VIDEOCOMPONENTCOMPONENTS-VIDEO VIDEOEE EEVIDEO VIDEOS-VIDEO S-VIDEOS-VIDEO S-VIDEOEE EECOMPONENT EE EECOMPONENT COMPONENTHDMIEEEECC (1080p)CC (480p ~ 720p)CC (480i/576i)CC (480p ~ 720p)EE CCEE CCEE CCCC (1080p) CC EECC EEEEEEEEEEEECOMPONENT ✳1COMPONENT ✳1COMPONENT ✳1COMPONENT ✳2VIDEO VIDEOVIDEOCOMPONENT ✳1 VIDEOCOMPONENT ✳2 S-VIDEO S-VIDEOS-VIDEOVIDEOCC (480i/576i)CC (1080p)CC (480p ~ 720p)EECC EECC CCCC CCCC (480i/576i) CC CCEE EEEEEEEECCEECCCOMPONENT ✳2COMPONENT ✳2COMPONENT ✳2EES-VIDEOS-VIDEO S-VIDEOS-VIDEOCOMPONENT ✳2 S-VIDEOEE EEHDMIEEEECC (480p ~ 720p)EE CCCC EECC CCCC (1080p) EE EEEE EECCCCCCCCCCVIDEO ✳2S-VIDEO ✳2S-VIDEO ✳2COMPONENTVIDEO VIDEOS-VIDEO S-VIDEOS-VIDEO S-VIDEOCOMPONENT EE EEEE EEHDMIHDMIHDMIHDMIHDMICC (1080p)CC (480p ~ 720p)CC (480i/576i)CC (480p ~ 720p)EEEECCEE CCEE CCCC (1080p) CC EECC EECCCCCCCCCCCOMPONENTCOMPONENT ✳1COMPONENT ✳1COMPONENT ✳1COMPONENT ✳2VIDEOCOMPONENTVIDEO ✳3 VIDEOVIDEOCOMPONENT ✳1 VIDEOCOMPONENT ✳2 S-VIDEO S-VIDEOS-VIDEO S-VIDEOHDMI ✳1HDMIHDMI ✳1HDMI ✳1HDMI ✳2HDMI ✳2CC (480i/576i)CC COMPONENT ✳2 S-VIDEOCOMPONENTS-VIDEOHDMI ✳2EEEECCCC (480i/576i)CC (480p ~ 720p)CC (1080p) CC CCCC CCCCCC COMPONENT ✳2COMPONENT ✳2 S-VIDEO S-VIDEOS-VIDEO S-VIDEOHDMI ✳2HDMI ✳2CC (480i/576i)CC COMPONENT ✳2 S-VIDEOHDMI ✳2CCCC480p ~ 720p : 480p/576p/1080i/720pEE : Not output1.HDMI MONITOR OUT:When there is no HDMI input signal and “HDMI” is selected for the “Scaler”setting, the signal is output as set with the “Resolution” setting.When “Component” is selected for the “Scaler” setting, the signal is outputwith the same resolution as the input signal.2.COMPONENT MONITOR OUTWhen “Component” is selected for the “Scaler” setting, the signal is outputas set with the “Resolution” setting. However, the output resolution islimited to a maximum of 480p/576p if the input signal is copyright-protected.✳1 : On screen display superimposed on video signal and output.✳2 : On screen display superimposed on S-Video signal and output.✳3 : Video signals are not output when the analog to HDMI convert functionis set to “ON”.: When “OFF” is selected for the “Analog to HDMI Convert” setting, novideo signals other than the HDMI input signal are output.: On screen display only displayed for SYSTEM SETUP, SURROUNDPARAMETER and OSD buttons.CC : Signal inputEE : No signalNOTES:• The MAIN ZONE video conversion function is compatible withthe following format: NTSC, PAL, SECAM, NTSC4.43, PAL-N,PAL-M and PAL-60.• When SECAM signals of video input are up-converted, thesignals are output in PAL format from the S-Video connector.• When the input signal is set to component video 1080p, thesignals cannot be output to the HDMI monitor output terminal.
