Getting Started Connections Setup Remote Control Multi-zone Information Troubleshooting SpecificationsListening to Music1 Use ui to select the menu, then press ENTER or pto select the music fi le to be played.2 Press ENTER or p.Playback starts.n Stopping playback temporarilyDuring playback, press ENTER or [1].Press again to resume playback.n Fast-forwarding or fast-reversingDuring playback, either press and hold [6] (to fast-reverse) or[7] (to fast-forward).n To cue to the beginning of a trackDuring playback, either press [8] (to cue to the previous track) or[9] (to cue to the next track).n To stopDuring playback, either press and hold ENTER or press [2].n Playing repeatedlyPress [CHANNEL –].[Selectable items] All One OFFMENU : ”Input Setup” – ”iPod” – “Repeat” (vpage 40)n Shuffling playbackPress [CHANNEL +].• When DENON control dock for iPod ASD-1R or ASD-11R is connected[Selectable items] Albums Songs OFF• When DENON control dock for iPod ASD-3N or ASD-3W is connected[Selectable items] ON OFFMENU : ”Input Setup” – ”iPod” – “Shuffl e” (vpage 41)• To check the name of the title, the artist or the album when playingin browse mode, press .• The folder name and the fi le name can be displayed in browsemode. Only alphanumeric characters and certain symbols can bedisplayed. Any characters that cannot be displayed are replaced with“ . (period)”.• The time (default : 30sec) for which the on-screen display aredisplayed can be set at menu “Manual Setup” – “Option Setup”– “On-Screen Display” – “iPod Information” (vpage 33).Press uio p to return to the original screen.• With the default settings, the iPod can be used connected to theVCR (iPod) connector.• Use the RESTORER mode to expand the low and high frequencycomponents of compressed audio fi les and achieve a richer sound.The default setting is “Mode3” (vpage 47).• Press or [POWER OFF] and set the AVR-2809CI’spower to the standby mode before disconnecting the iPod. Alsoswitch the input source to one to which the menu “iPod Dock” isnot assigned before disconnecting the iPod.• When using an ASD-3N or ASD-3W control dock for iPod, refer tothe respective manual to operate.3 To operate using the main remote control unit, set theremote control unit to the iPod mode.(vpage 61 “Remote Control Unit Operations”)4 Press [SEARCH] and hold it down for a 2 seconds ormore to select the display mode.To switch between modes, press and hold down the button.When remote mode is active, “Remote” is displayed.[Selectable mode] Browse mode Remote modeDisplay location Main unit display iPod displayPlayablefilesAudio file S SVideo file S z1 S z2ActivebuttonsRemotecontrol unit(AVR-2809CI)S SiPod A Sz1 : When using an ASD-3N or ASD-3W control dock for iPod.z2 : Video may not be output, depending on the combination ofASD-1R or ASD-11R and iPod.Viewing Still Pictures or Videos on theiPodPhoto and video data on the iPod can be viewed on the monitor.Only for iPod equipped with slideshow or video functions. (Whenusing an ASD-1R or ASD-11R)1 Press and hold [SEARCH] to set the Remote mode.“Remote iPod” is displayed on the AVR-2809CI’s display.2 Watching the iPod’s screen, use ui to select“Photos” or “Videos”.3 Press [ENTER] until the image you want to view isdisplayed.• “TV Out” at the iPod’s “Slideshow Settings” or “Video Settings”must be set to “On” in order to display the iPod’s photo data or videoson the monitor. For details, see the iPod’s operating instructions.• When viewing an iPod video fi le, select “iPod” - “Video” in browsemode. (When using an ASD-3N or ASD-3W)NOTE• Depending on the type of iPod and the software version,somefunctions may not operate.• DENON will accept no responsibility whatsoever for any loss of iPoddata.Playback
