Denon CEOL RCD-N8 Owner's Manual

Also see for CEOL RCD-N8: Service manual

14Setting the general [General]Speaker OptimizationAn optimizing filter suited for the properties of the speakers (SC-N8)can be used.1 Press SETUP.Turns on the Menu settings modeand the Menu appears on the display(vpage 11 “Menu map”).ADDCALLFAVORITESEARCH. / ABCa/ADEFGHI JKL MNOPQRS TUV WXYZ*1 2 34 5 67 8 9+10 0RC-1174CH - +CHTUNE +TUNE -ANALOG INTUNER DIGITAL INPOWERCLOCK DIMMERSLEEPMUSICSERVERINTERNETRADIO ONLINEMUSICVOLUMESDBTONEMUTETOP MENU INFOMODECLEARUSBiPod CDRANDOM REPEAT PROGRAMENTERSETUP2 Use ui and ENTER toselect “General” – “SpeakerOptimization”, then pressENTER or p.“Speaker Optimization” menu appears.3 Use ui to select “On”, thenpress ENTER or p.ON The response is optimized for the speakers (SC-N8, soldseparately).OFF The response is flat.LanguageSets the language for display the menu.• The factory language setting is “English”.1 Press SETUP.Turns on the Menu settings modeand the Menu appears on the display(vpage 11 “Menu map”).ADDCALLFAVORITESEARCH. / ABCa/ADEFGHI JKL MNOPQRS TUV WXYZ*1 2 34 5 67 8 9+10 0RC-1174CH - +CHTUNE +TUNE -ANALOG INTUNER DIGITAL INPOWERCLOCK DIMMERSLEEPMUSICSERVERINTERNETRADIO ONLINEMUSICVOLUMESDBTONEMUTETOP MENU INFOMODECLEARUSBiPod CDRANDOM REPEAT PROGRAMENTERSETUP2 Use ui and ENTER to select“General” – “Language”, thenpress ENTER or p.English / Deutsch / Français /Italiano / Nederlands / Español /SvenskaAuto-StandbyWhen this unit is in the stop state and there is no input signal andoperation for 30 minutes, it automatically enters the standby mode.For the input source “Analog In 1”, “Analog In 2” and “PortableIn” only, when no operation is performed for eight hours, this unitautomatically enters the standby mode.• The default setting is “On”.1 Press SETUP.Turns on the Menu settings modeand the Menu appears on the display(vpage 11 “Menu map”).ADDCALLFAVORITESEARCH. / ABCa/ADEFGHI JKL MNOPQRS TUV WXYZ*1 2 34 5 67 8 9+10 0RC-1174CH - +CHTUNE +TUNE -ANALOG INTUNER DIGITAL INPOWERCLOCK DIMMERSLEEPMUSICSERVERINTERNETRADIO ONLINEMUSICVOLUMESDBTONEMUTETOP MENU INFOMODECLEARUSBiPod CDRANDOM REPEAT PROGRAMENTERSETUP2 Use ui and ENTER to select“General” – “Auto-Standby”,then press ENTER or p.“Select Auto-Standby” menu appears.3 Use ui to select “On”, thenpress ENTER or p.The setting is entered.NOTEIn the following situations, the Auto-standby function does not operate.• When the source is “Tuner”, “iPod” (Remote mode) or “AirPlay”.• During CD playback or pause.Firmwaren Update• In order to update the firmware, the environment and settingsrequired for connecting to broadband internet are needed(vpage 9).• Perform the firmware update operation after at least 2 minutes haselapsed since turning this unit’s power ON.1 Press SETUP.Turns on the Menu settings modeand the Menu appears on the display(vpage 11 “Menu map”).ADDCALLFAVORITESEARCH. / ABCa/ADEFGHI JKL MNOPQRS TUV WXYZ*1 2 34 5 67 8 9+10 0RC-1174CH - +CHTUNE +TUNE -ANALOG INTUNER DIGITAL INPOWERCLOCK DIMMERSLEEPMUSICSERVERINTERNETRADIO ONLINEMUSICVOLUMESDBTONEMUTETOP MENU INFOMODECLEARUSBiPod CDRANDOM REPEAT PROGRAMENTERSETUP2 Use ui and ENTER to select“General” – “Firmware” –“Update”, then press ENTER orp.Check For Update Check for firmware updates. You can also checkapproximately how long it will take to completean update.Update Start Execute the update process.• If updating fails, the set automatically retries, but if updating is stillnot possible, one of the messages shown below is displayed. Ifthe display reads as shown below, check the settings and networkenvironment, then update again.Display DescriptionUpdating fail Updating failed.Login failed Failure to login to server.Server is busy Server is busy. Wait a while then try again.Connection fail Failure in connecting to server.Download fail Downloading of the firmware has failed.