Denon DBP-4010UD Owner's Manual

Contents

TroubleshootingInformationHDMI Control FunctionPlaybackSetupGetting Started SpecificationsENGLISH1. Home Theater Playback – Playing Back Using Multi-channel System –ConnectionsWhen connecting with an HDMI cable, press and set it to “HDMI On”.DBP-4010UD automatically detects audio/video signal supported by the connected HDMI deviceand outputs the signal. To change the setting, see “HDMI Setup” on the GUI menu (vpage 23,24).NOTEWhen you press and set it to “HDMI On”, no video signals are output from the componentvideo outputs.To disable video or audio output from the HDMI terminal, set “Video Out” of “Pure Direct Setup”,which outputs high quality analog audio to “Off”. To enable the HDMI signal output, set the PureDirect mode to one of the following setting:Pure Direct mode “Off” or “User Preset 1” or “User Preset 2” (b)(“Playing Back High-Quality Audio (Pure Direct Function) ” vpage 38)Do this after setting “Pure Direct Setup” – “User Preset 1” or “User Preset 2” – “Video Out” on GUImenu to “On” (vpage 28).•••••bUsing an HDMI Cable to Connect to an AV Amp or TelevisionDuring “HDMI On”Audio/video signals are output from the HDMI terminal.When the HDMI video resolution is set to “Auto” as described in “About HDMI Video ResolutionSetting” (vpage 13), the DBP-4010UD outputs the highest resolution video signal that is supportedby the connected equipment.*/)%.*AV Amp orTVDuring “HDMI Off”Audio/video is not output from the HDMI terminal.NOTEWhen audio/video signals are output from the HDMI terminal, no video signals are output from thecomponent terminals.When a signal comprising 24 frames per second, such as 1080P24, is output from the HDMI terminal,no video signals are output from the video or S-Video outputs.••Connection to a device with a DVI-D terminalIf you use a HDMI/DVI-D conversion cable (sold separately), HDMI video signals are converted to DVI-D signals, enabling connection to a device with a DVI-D terminal.nNOTEIn this case, the audio signal is not output. Make the appropriate audio connections for your devices.(vpage 14 ~ 20).The video signal will be in RGB format.You cannot output to a DVI-D device that does not support HDCP (high-bandwidth digital contentcopyright protection system).Video may not be output depending on the combination of devices.••••Setting HDMI Video OutputMake HDMI Output Signal and HDMI Control Function Settings“HDMI Setup” (vpage 23, 24)Make the Video Output Signal Setting for the Connected Television“Video Setup” (vpage 24)About HDMI Video Resolution SettingChange the HDMI video resolution by pressing . Switch the output mode as follows. Defaultsettings are underlined.Auto 480/576i1080P24 1080P 1080i480/576P720PSource DirectIf the HDMI resolution is not set to “Auto”, set it to correspond with the resolution of your television.Images will not be projected normally if the television resolution and DBP-4010UD’s output resolutiondo not match.Audio and video will be temporarily interrupted if the power of the connected device currently playingback is turned off, or input is switched.When you change the HDMI video resolution of the DBP-4010UD, it takes from a few seconds up toabout 10 seconds for validation between the DBP-4010UD and the connected device. Audio/video isnot output during this period.When outputting deep colour or 1080p, etc., we recommend you use High Speed HDMI cable forenhanced high-quality playback.nnn•••••Required Settings for HDMI Connection(480/576 interlaced) (480/576 progressive)(720 progressive)(1080 interlaced)(1080 progressive)(1080 progressive, 24-frame)(Source direct)(Auto)When outputting a video signal comprising 24 frames per second from the HDMI terminal, select“1080P24” or “Source Direct” after setting the GUI menu “HDMI Setup” – “I/P Direct” (vpage 23) to“On”.See overleaf