Eaton HALO AL3150LPCGY Instruction Manual
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1Instruction M anual / M anuel d ’ instructions/ I nstruccionesPACKAGING CONTENTS /CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE2. Using the pattern on the box, mark and drill holes for mounting.NOTE: Mount this fixture in an upright and level position.3. Install the two bottom mounting screws (C) first, leaving enough room between themounting screws and the mounting surface to accommodate mounting the fixture.4. Screw the top mounting screw (C) into the predrilled hole and back the screw out. Thiswill leave the hole threaded and make installation of the fixture easier.5. Remove lens by loosening the two screws inside the lens. Do not remove the screws.6. Remove access cover (B) from fixture (A). Installthe first conduit connector and conduit (soldseparately) into the access cover (B) (Fig. 1).7. Feed supply wires into conduit. Attach ground wirethat is attached to fixture housing (A) to the junctionbox earth ground wire.8. Connect the black fixture wire to the black supplywire (hot) with UL-approved wire connector (E).Connect the white fixture wire to the white supplywire (neutral) with UL-approved wire connector (E).NOTE: Be careful to connect the wires correctly.Make sure no bare strands of wire extend from thewire nut or other approved wire connectors (E).9. Attach access cover (B) to the light fixture (A)using the two access cover mounting screwsprovided (F) (Fig. 1).NOTE: Make sure all wiring is placed into the arm prior to tightening the accesscover screws.10. Place the fixture (A) on the two lower mounting screws (C) and install the upper mountingscrew (C). Tighten all mounting screws to secure the fixture (A).11. Reinstall the lens, making sure to tighten the two screws to secure the lens tothe fixture (A).12. Install photo control by inserting into socket and turning clockwise until prongs lock intoposition. Photo control sensor window should aim North for best performance. To aimphoto control, loosen the two screws on the socket cover and rotate socket until the arrowon the socket aligns with North. Tighten the socket screws to lock in place and install thephoto control.13. Connect second conduit and conduit connector at the junction box (Fig. 1).NOTE: This fixture can be mounted on 1-5/8 in. diameter extension arms (sold separately).When installing fixture onto an extension arm, remove the access cover (B) and use theincluded pole mounting clamp (D) and access cover mounting screws (F).14. Turn power back ON.ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Adjustable wrench or ratchet wrench with 10mm socket• Drill with 3/16 in. drill bit• 1/2 in. diameter conduit (if applicable, length depends on application)• 1/2 in. watertight conduit connectors (if applicable)• Wire connectorsIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location use.• Read and follow these instructions.• Disconnect at fuse or circuit breaker before installing or servicing.• Edges may cut. Handle with care.CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Upside down installation can result in overheating or accumulation of water in fixture.Install right side up.• This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may causeundesired operationWARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS.MOUNTING AND WIRING YOUR FIXTURENOTE: This fixture is intended to be conduit connected to a properly installed and properlygrounded metal weatherproof junction box (not included). All conduit connectors, conduit, andjunction boxes (sold separately) should be cULus Listed suitable for wet locations.1. Turn off the power at the main fuse/breaker box.ENGLISHWARNINGA. Light fixtureAppareil d’éclairageAccesorioB. Access coverCache d’accèsCubierta de accesoC. (3) Mounting screws(3) Vis de montage(3) Tornillos de montajeD. Pole mounting clampPatte pour montagesur brasAbrazadera paramontaje de posteE. (3) Wire connectors(3) Capuchons de connexion(3) Conectores de cablesF. (2) Access cover mounting screws(2) Vis de montage du cache d’accès(2) Tornillos de la cubierta de acceso1ConduitConduitconnectorJunctionboxABBronze/Bronze/BronceAL3150LPCBZAL5550LPCBZAL5550LPCBZHB. Light sensorCapteur du luminaireSensor de luzGray/Gris/GrisAL3150LPCGYAL5550LPCGY |
Related manuals for Eaton HALO AL3150LPCBZ
Eaton HALO AL1550LPCBZ Instruction Manual
Eaton ALL-PRO AL3050LPCGY Instruction Manual
Eaton HALO AL6501FL Instruction Manual
Eaton HALO MS34 Instruction Manual
Eaton HALO MT125 Instruction Manual
Eaton Halo MST1850LW Instruction Manual
Eaton HALO VT100G Instruction Manual
Eaton HALO FE13PC Instruction Manual
Eaton HALO MS276RD Instruction Manual
Eaton HALO FW26PCI Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine