Eaton HALO S1FB06M2B Instruction Manual

Eaton HALO S1FB06M2B Instruction Manual Manual pdf 1 page image

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1PACKAGING CONTENTS/CONTENU D E L ’ E MBALLAGE/CONTENIDO D E L P A Q U E T EInstruction Manual / Manuel d’instructions/ Instrucciones®FOR BEST RESULTS• Install fixture 6-12 feet above ground.• Place batteries in unit and test fixture beforeinstalling.• Locate fixture so motion moves across thedetection zone (Fig. 1).• Do not mount fixture close to reflective surfacessuch as windows, white walls, white surfacesand water.• Locate fixture away from heat producing sourcesto prevent false triggering. Also, be very carefulnot to include objects such as windows, whitewalls and water in the detection zone.• Locate fixture away from moving objects such astrees, large shrubs and street trafficMOUNTING YOUR FIXTURENote: Do not mount within 1 foot of a highly refletiveexterior inside corner (Fig. 2).1. Locate area in which you would like to install yourlight fixture.2. Using the fixture mounting screws (C) provided,mount the snap-in mounting bracket (B) to a solidsurface 6-12 feet above ground by placing thescrews through the center holes of the bracket.Make sure the arrow on the bracket is pointing up(Fig. 3). The provided screw anchors may be neces-sary depending on the material the fixture is beingmounted to.3. Remove the battery cover by unscrewing the thumbscrew (Fig. 4).4. Insert 3 D-Cell, 1.5V Alkaline Batteries. Be sure tomatch up the polarity markings on the batteries withthe polarity markings in the fixture (Fig. 5).5. Reinstall the battery cover by sliding in the two lock-ing tabs on the battery cover with the luminaire (Fig.4). Then use your hand to completely screw in thethumb screw to fasten the battery cover to the fixture.6. Slide fixture down over the snap-in mountingbracket, making sure that the fixture engages theguide ribs. Continue sliding down until the fixturesnaps into the locking tab (Fig. 6).7. Slide power switch to AUTO (Fig. 7).ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• 3, 1.5V D-Cell Alkaline BatteriesIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• Disassembling your fixture will void the warranty.• Fixture is suitable for wall mount only. NOT suitable for ground mount installation.• Use only Alkaline Battery chemistry with fixture.• Use only 1.5V, D-Cell Batteries with fixture.FCC DECLARATION OF CONFORMITYThis device complies with part 15 of the FCC Rules. Operation is subject to the following 2conditions: (1) This device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Consult the dealer or an experienced radio/TV technician for help.WARNING: FCC Regulations state that any unauthorized changes or modificationsto this equipment not expressly approved by the manufacturer could void the user’sauthorization to operate this equipment.SAVE THESE INSTRUCTIONS.A. Light fixtureAppareil d’éclairageAccesorioENGLISHC. (2) Fixture Mounting Screws and Screw Anchors(2) Vis de montage et vis d’ancrage pour le luminaire(2) Tornillos de montaje del accesorio y anclajes de tornilloB. Snap-in Mounting bracketSupport de montage encliquetableSoporte de montaje a presión(Bronze/Bronze/Bronce)S1FB06M2BS1FB10M2B13451 ft.1 ft.1 ft.2