Eaton Halo FSL503TIB Instruction Manual

Questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1Instruction Manual/ InstruccionesPACKAGING CONTENTS/CONTENIDO DEL PAQUETE- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.- Consult the dealer or an experienced radio/TV technician for help.WARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS.FOR BEST RESULTS• Install light 8-16 feet above the ground.• Do not mount fixture close to reflective surfacessuch as windows, white walls, white surfacesand water.• When installing two fixtures on one switch,make sure the switch is rated for at least a1 A inductive load.• When mounting coverplate, make sure the photosensor orientation is at the bottom.• When mounting to a wall, make sure the fixture is7 in. on center away from eave and 13 inches oncenter away from inside corner of the exteriorwall (Fig. 1).ADJUSTING THE COLOR TEMPERATURE (CCT)• This product features selectable white colortuning. Choose between three preset light colorson the center dial of the base housing before,during or after installation (fig. 2):• These settings are designated by the abbreviationslocated on the center dial on the base housing(fig. 2):3K = 3000K CCT, or soft white4K = 4000K CCT, or neutral white[factory default]5K = 5000K CCT, or daylight• Use a flathead or Phillips head screwdriver to rotate thedial so the arrow points toward the desired setting.• DO NOT USE a power tool or over-rotate the dial.MOUNTING AND WIRING YOUR FIXTUREWARNING: Risk of electric shock. Disconnectpower at fuse or circuit breaker before installingor servicing.NOTE: Fixture can be wall or eave mounted (Fig. 3).ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Weatherproof silicone caulkIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• Risk of fire/electric shock. If not qualified, consult an electrician.• Disconnect power at fuse or circuit breaker before installing or servicing.CAUTION• Connect fixture to a 120V-277V volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Fixture designed for wall or eave mount to a junction box only. Mount fixture to agrounded, recessed-mounted standard junction box marked for use in wet locations.• Fixture can be mounted to an outdoor rated surface mount junction box or when usedwith the included adaptar plate kit. See kit instructions for proper installation methods.• This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-signed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energyand if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by oneor more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.FSL503TIBFSL503TIWA. Light fixtureAppareil d’éclairageAccesorioENGLISHD. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws(use the size that fits your junction box)(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pouboîtier de jonction (choisissez la dimension convenantà votre boîtier de jonction)(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4 pulg.para montaje de la caja de conexión (utilice el tamaño que mejorse adecue a su caja de conexión)F. Support hookCrochetGancho de soporteC. GasketJointJuntaH. (2) Decorative screw cover caps(2) cache-vis décoratifs(2) Cubiertas tapatornillos decorativasG. (2) #8-32 x 1-1/4 in. covermounting screws(2) vis de protection nº 8de 32 x 1-1/4 po(2) Tornillos #8-32 x 1-1/4 pulg.de montaje de la cubiertaB. Mounting bracketSupport de montageSoporte de montaje7 in.13 in.113 in.2E. Adapter Plate KitPlaque adaptatrice troussePlaca daptadora equipo3Wall mountEave mount