GE NetworX NX-6V2 Installation And Startup

Also see for NetworX NX-6V2: User manual Installation instructions

Contents

NX-6V2 Control 13L 8 COMMUNICATOR FORMAT FOR PHONE 2 1............. numericalLocation 8 contains the communicator format used to transmit to the receiver connected to Phone 2. Consult the instruction manual foryour central station receiver to determine which format is compatible, and select from Table XII-1 COMMUNICATOR FORMATSELECTIONS on page 11. If you require a format other than those listed, review the override options described in Location 18 to buildthe appropriate format. A "15" must be programmed in location 8 in addition to the entries in location 18 in order to create a specialformat. If this location contains a "0", format 1 will be used when Phone 2 is dialed.9 DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE 2 2............. numericalSegment 1, Dial attempts: Segment 1 of Location 9 is used to enter the number of dial attempts (1 to 15 attempts) the communicatorwill make to Phone 2 before ending the notification process. Factory default is "8" and the communicator will make the same numberof attempts as those programmed in location 3.Segment 2, Phone 2 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-6V2 to make the designatednumber of attempts to Phone 1 before setting the "Fail To Communicate" condition and stop reporting. Programming a "1" in thissegment will cause the NX-6V2 to stop trying to communicate after the designated number of attempts have been made to Phone 2. Ifa "2" is programmed in this segment, it will cause the NX-6V2 to make the dial attempts in increments of two. The first two attempts willbe made to Phone 2, the next two attempts to Phone 1, then repeating until the total number of attempts designated in Segment 1 iscompleted.REPORTING EVENTS TO PHONE NUMBER 2Phone 2 can be used to back up Phone 1 or for a second receiver to multi-report or split report events. Phone 2 has two programminglocations that are used to select which events are reported to this phone number. Location 10 is used to select which events arereported to Phone 2, and location 11 is used to select which partitions are reported to Phone 2. If dual or split reporting is not desired,location 10 and location 11 should be left at the factory default of "0". If multi-reporting or split reporting is desired, and the split isbased on the event type (such as alarm, open close etc.), location 10 should be used to select only those events that should bereported to Phone 2, and location 11 should be left at the factory default of "0". If dual or split reporting is desired, and the split isbased on partition, then location 10 should be programmed as "0", and location 11 should be used to select those partitions that shouldbe reported to the Phone 2. If no events should be reported to Phone 2, both locations should be "0".10 EVENTS REPORTED TO PHONE 2 2............. feature selectSegment 1:1 = Alarms and Alarm Restores.2 = Opening and Closings.3 = Zone Bypass and Bypass Restores.4 = Zone Trouble and Trouble Restores.5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.6 = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore.7 = Test Reports.8 = Start and End programming, Download complete.Segment 2:1 = Zone and Box Tamper and Tamper Restore.2 = Auxiliary Power Overcurrent and Ground Fault and Restore for both.3 = Sensor Missing and Restore.4 = Sensor Low Battery and Restore.5 = Expander Trouble and Restore.6 = Fail To Communicate.7 = Zone Activity Monitor.8 = Reserved.11 PARTITIONS REPORTED TO PHONE 2 1............. feature selectLocation 11 is used when events to be reported to a phone number are based upon the partition regardless of the event. If this locationis used, location 10 should be "0".Segment 1:1 = Partition 1 2 = Partition 212 PROGRAMMING PHONE 3 20........... numericalPhone 3 is programmed in location 12. A "14" indicates the end of the phone number. Delays of four seconds can be programmed atany point in the phone number by programming a "13" in the appropriate segment. If tone dialing is desired, program a "15" in thesegment where tone dialing should begin. If the entire number should be tone dialing, program a "15" in the first segment. Program anA11" for a Ar@, and a A12" for a A#@. Caution: A call-waiting cancel on a non- call waiting line will prevent successful connection to thecentral station.