GE NetworX NX-6V2 Installation And Startup

Also see for NetworX NX-6V2: User manual Installation instructions

Contents

NX-6V2 Control 39XV. GLOSSARYAbortIf enabled, the NX-6V2 will wait the programmed number of seconds in location 40 prior to sending an alarm. During this delay time, the“Cancel” LED will flash. To abort the report, type in a code and press the Cancel key. The LED will extinguish. If the report is notaborted within the allotted time, the LED will extinguish when the report is sent. ADialer Delay@ must be enabled in the ACharacteristicSelect@ of locations 110-169. (Loc 40 & 110-169, pg 19 & 25-29)AC Fail / Low Battery Report / WarningThe NX-6V2 can be programmed to report AC failure and/or Low Battery conditions to the central station. It can also be programmed tosound the keypad immediately upon detection of the condition. The AC failure report/warning can be delayed. (Loc 37 & 39, pg 18)AC Power / Low Battery Sounder AlertIf enabled, the NX-6V2 will beep the keypad sounder upon arming or disarming if the AC power is missing or a low battery has beendetected. (Loc 23, pg 15)Arm / Disarm CodesThe NX-6V2 can have 40 four-digit codes or six-digit codes to arm/disarm the control. All codes must have the same number of digits.The factory default for User #1 is ÎÏÐÑ when using a 4-digit code, or ÎÏÐÑÒÓ for a 6-digit code. This code can then be usedto enter the new arm/disarm codes. (Loc 41, pg 20)Automatic Arming NOTE: This feature must be disabled for UL installationsIf programmed, the NX-6V2 will Auto Arm at a specified time. At this time, the keypad will beep for 50 seconds before the panel arms.The arming process will be stopped if a code is entered on the keypad. The NX-6V2 will attempt to arm after every 45 minutes ofinactivity until the next “opening” time (loc. 52), or until the system is armed. The 45-minute timer will be extended when there is activityin the building causing the "Ready" LED to turn off and on. If closing reports are sent, the user code will be 97. (Loc 23 & 52-55, pg 15& 22)Automatic Bypass / Instant ArmingWhen enabled, the control panel can automatically bypass interior follower zones if an exit is not detected during the exit delay time.Entry delay zones can also be made instant. (Loc 23, segments 1 & 3, pg 15)Auto Cancel / AbortIf enabled, the Cancel and/or Abort features will be automatic (pressing the [Cancel] button is not required). The Cancel and Abortfeatures, in locations 23 & 40 respectively, must be enabled to permit this Auto feature to work. For proper operation of these features,ADialer Delay@ must be enabled in the ACharacteristic Select@ of locations 110-169 Zone Types. (Loc 41, pg 20)Auto TestThis feature will cause the panel to call the central station to report a communicator test at a specified interval. (Loc 51, pg 22)Auxiliary OutputsThe NX-6V2 has 4 programmable outputs that can be used to activate relays, LED=s, etc. (See the terminal description on pg 6 and Loc45-50, pg 20)Auxiliary Power Over-currentThe NX-6V2 will illuminate the "Service" LED on the keypad whenever too much current is drawn from any device powered by thesystem. This condition can be reported to the central station. (Loc 37, pg 18)Box TamperThe NX-6V2 has an input for a normally closed tamper switch (see terminal drawing). The Box Tamper can be programmed to reportand/or sound the siren and/or the keypad. These terminals can be enabled or disabled in programming. (Loc 37 & 39, pg 18)Built In Siren DriverThe NX-6V2 has a built-in 112db-siren driver. When desired, this built-in driver can be easily converted to a 1-amp voltage outputthrough programming. (Loc 37, pg 18)Bypass ToggleThis feature will enable the end user to toggle (turn on or off) the bypass of an interior zone with the system armed by pressing the[Bypass] key. (Loc 23, pg 15)Call BackWhen enabled, the control will use the call back phone number to call the download computer before beginning a download. (Loc 21,pg 15)CancelIf enabled, the NX-6V2 will send a "Cancel" report if when the system is disarmed and the [Cancel] button is pressed within 5 minutes ofan alarm. Once the [Cancel] key is pressed, the "Cancel" LED will illuminate until the central station acknowledges the "Cancel" report.ADialer Delay@ must be enabled in the ACharacteristic Select@ of locations 110-149. (Loc 23, pg 15)Code Required OptionsThe NX-6V2 can be programmed to require a code for bypassing zones and/or initiating a download using the r98 or r99function. (Loc 23 & 41, pg 15 & 20)Communication FormatsThe NX-6V2 can report in multiple formats. It is recommended that you use Contact ID or SIA formats if possible. If you wish to report toa pager or in a 4+2 format to a central station, you must program each code to be reported. (Loc 56-83 & 111-169, pg 23-24 & 25-29)Cross ZoningThis feature requires two or more trips on a zone or zones programmed as "cross zones" within a specified time before reporting analarm. During the time between trips, the NX-6V2 can be programmed to sound the keypad and/or the siren. The NX-6V2 can also beprogrammed to report an alarm after two or more trips on the same zone. (Loc 37, 39, 40 & 110-149, pg 18, 19, 25-29)