GE NetworX NX-6V2 Installation And Startup

Also see for NetworX NX-6V2: User manual Installation instructions

Contents

14 NX-6V2 Control13 ACCOUNT CODE FOR PHONE 3 6 ............ numericalThe account code sent when Phone 3 is dialed is programmed in location 13. Program a A10" in the segment immediately after the lastdigit of the account code. If the account code is 6 digits long, program all 6 segments. If location 6 is left unprogrammed, accountcode 1 will be used when the Phone 3 is dialed.14 COMMUNICATOR FORMAT FOR PHONE 3 1 ............ numericalLocation 14 contains the communicator format used to transmit to the receiver connected to phone 3. Consult the instruction manualfor your central station receiver to determine which format is compatible, and select from Table XII-1 COMMUNICATOR FORMATSELECTIONS on page 11. If you require a format other than those listed, review the override options described in Location 18 to buildthe appropriate format. A "15" must be programmed in location 14 in addition to the entries in location 18 in order to create a specialformat. If this location contains a "0", format 1 will be used when Phone 3 is dialed.15 DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE 3 2 ............ numericalSegment 1, Dial Attempts: Segment 1 of Location 15 is used to enter the number of dial attempts (1 to 15 attempts) thecommunicator will try to Phone 3 before ending the notification process. Factory default is "8" and the communicator will make thesame number of attempts as those programmed in location 3.Segment 2, Phone 3 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-6V2 to make the designatednumber of attempts to Phone 2 before setting the "Fail To Communicate" condition and stop reporting. Programming a "1" in thissegment will cause the NX-6V2 to stop trying to communicate after the designated number of attempts have been made to Phone 3. Ifa "2" is programmed in this segment, it will cause the NX-6V2 to make the dial attempts in increments of two. The first two attempts willbe made to Phone 3, the next two attempts to Phone 2, then repeating until the total number of attempts designated in Segment 1 iscompleted.REPORTING EVENTS TO PHONE NUMBER 3Phone 3 can be used for a third receiver to multi-report or split report events. Phone 3 has two programming locations that are used toselect which events are reported to this phone number. Location 16 is used to select which events are reported to Phone 3, andLocation 17 is used to select which partitions are reported to Phone 3. If dual or split reporting is not desired, location 16 and location17 should be left at the factory default of "0". If multi-reporting or split reporting is desired and the split is based on the event type(such as alarm, open/close, etc.), then location 16 should be used to select only those events that should be reported to Phone 3 andlocation 17 should be left at the factory default of "0". If dual or split reporting is desired, and the split is based on partition, thenlocation 16 should be programmed to "0" and location 17 should be used to select those partitions that should be reported to Phone 3.If no events should be reported to Phone 3, both locations should be "0".16 EVENTS REPORTED TO PHONE 3 2 ............ feature selectSegment 1:1 = Alarms and Alarm Restores.2 = Opening and Closings.3 = Zone Bypass and Bypass Restores.4 = Zone Trouble and Trouble Restores.5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.6 = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore.7 = Test Reports.8 = Start and End programming, Download complete.Segment 2:1 = Zone and Box Tamper and Tamper Restore.2 = Auxiliary Power Overcurrent and Ground Fault and Restore for both.3 = Sensor Missing and Restore.4 = Sensor Low Battery and Restore.5 = Expander Trouble and Restore.6 = Fail To Communicate.7 = Zone Activity Monitor.8 = Reserved.17 PARTITIONS REPORTED TO PHONE 3 1 ............ feature selectLocation 17 is used when events to be reported to a phone number are based upon the partition regardless of the event. If this locationis used, location 16 should be "0".Segment 1:1 = Partition 1 2 = Partition 2