Garmin GMX 200 Installation Manual

Also see for GMX 200: Pilot's guide Reference guide Installation Pilot's Guide & Reference Specification

Contents

TYPICAL CONNECTION TO ARINC 429 TRAFFIC SOURCESGMX 200 I/O MFDARINC 429 INDISCRETE OUT 2DISCRETE OUT 3AB34338285P2002TRC 497 TRC 899P1 P1KTA 810 KMH 820J10 J105958674243211954552325455232L3 COMM 5 HONEYWELL 6 TRAFFIC ADVISORYSYSTEMARINC 429 OUTABSTANDBY/OPERATEFUNCTIONAL TEST(OPTIONAL) 4GMX 200 I/O MFDRS-232 OUT 3RS-232 IN 3SERIAL GND 36725P2001RYAN9900B9900BXP1222021RS-232 RXRS-232 TXGROUNDTCAD87CONNECTIONS TO RYAN TCADSSGMX 200 I/O MFDARINC 429 INDISCRETE OUT 2ABP200259586GARMINGTX 33GTX 330P3301302846TRAFFIC ADVISORYSYSTEMTIS CONNECT SELECTABCONNECTIONS TO TIS-A SOURCEARINC 429 OUT 29NOTESALL WIRES 24 AWG OR LARGER UNLESS OTHERWISE SPECIFIED.AT GMX 200, CONNECT SHIELD GROUNDS TO THE CONNECTOR BACKSHELL – THE SHIELD LEADS MUST BE LESS THAN 3.0”.CONNECT OTHER SHIELD GROUNDS TO AIRCRAFT CHASSIS WITH AS SHORT A CONDUCTOR AS PRACTICAL.THESE OPTIONAL DISCRETE CONNECTIONS ARE NOT REQUIRED IF THE GMX 200 IS CONFIGURED FOR ‘TAS+DISP’. IN THIS CASE, THE GMX 200WILL NOT CONTROL THE TRAFFIC ADVISORY SYSTEM OPERATION.GMX 200 MUST BE CONFIGURED FOR TRAFFIC SOURCE: TAS OR TAS+DISP (SEE NOTE 4), AND TRAFFIC FUNCTION MUST BE ENABLED. SKYWATCHMUST BE CONFIGURED FOR AN ARINC 735 TYPE 1 DISPLAY. THE SKYWATCH SOFTKEY (DISCRETE) INPUTS MAY BE DRIVEN BY MULTIPLE DISPLAY SOURCES.GMX 200 MUST BE CONFIGURED FOR TRAFFIC SOURCE: TAS OR TAS+DISP (SEE NOTE 4), AND TRAFFIC FUNCTION MUST BE ENABLED. KMH 880 KMH 820) ANDKTA 870 (KTA 810) SYSTEMS MUST HAVE TRAFFIC CONFIGURED FOR ‘CONTROLLER TYPE: DISCRETE’ AND ‘DISPLAY VALID: IGNORE’. THE KTA 810/KMH 820INPUTS CANNOT BE DRIVEN BY MULTIPLE DISPLAY SOURCES.TRAFFIC FUNCTION IS ONLY AVAILABLE WITH THE GMX 200 I/O MODEL. RS-232 PORTS 1, 2, 4 OR 5 MAY BE USED INSTEAD OF PORT 3. GMX 200 MUST BECONFIGURED FOR RYAN TCAD SOURCE: PORT 3 (OR APPROPRIATE PORT) AND TRAFFIC FUNCTION MUST BE ENABLED.TCAD 9900B VERSION 1.08 (OR LATER) OR 9900BX VERSION 1.11 (OR LATER) IS REQUIRED FOR PROPER OPERATION WITH GMX 200.GMX 200 MUST BE CONFIGURED FOR TRANSPONDER TIS SOURCE: GTX 330 AND THE TRAFFIC FUNCTION MUST BE ENABLED. THE GTX 33/330 ARINC 429OUTPUT MUST BE SET TO ‘GARMIN W/TIS’. THE ‘TIS CONNECT SELECT’ DISCRETE INPUT MAY BE DRIVEN BY MULTIPLE DISPLAY SOURCES.ONLY ONE TRAFFIC SOURCE MAY BE CONNECTED TO THE GMX 200. IN ADDITION TO THE TRAFFIC SOURCES CONTAINED IN THIS FIGURE,THE GDL 90 IS ALSO CONSIDERED A TRAFFIC SOURCE.1.2.4567893.Figure E-7. TrafficGMX 200 Installation Manual Page E-9190-00607-04 Revision F