IHP CAPELLA 33 Installation And Operation Instructions Manual

Also see for CAPELLA 33: Installation and operation instructions

Contents

IHP CAPELLA 33 Installation And Operation Instructions Manual Manual pdf 3 page image

WARNINGDo not install or operate this fire-place through a switch wired in the120 VAC or 240 VAC circuits. Theonly approved wiring for a switchis through the low voltage circuit(24 VAC) as shown on Page 14.NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 3CONGRATULATIONS!In selecting this Innovative Hearth Products (IHP) electric fireplace, you have chosenthe finest and most dependable fireplace found anywhere. A beautiful and prestigiousaddition to the finest homes.Please read and carefully follow all of the instructions found in this manual. Pleasepay special attention to the safety instructions provided in this manual. The instruc-tions included here will assure that you have many years of dependable and enjoyableservice from your product.TABLE OF CONTENTSImportant Safety Information ............Page 2Packaging List...................................Page 3Introduction ......................................Page 3General Information ..........................Page 3Locating Fireplace .............................Page 3Tools/Supplies Required .................. Page 3Framing Specifications ..................... Page 4Fireplace Specifications.................... Page 4Clearances ....................................... Page 5Pre-installation ................................. Page 5Installation Steps ............................. Page 5Electrical Connections ...................... Page 5Final Finishing .................................. Page 6Break-In Period ................................ Page 6Control Panel Operation ................... Page 6Remote Control Operation ............... Page 7Maintenance..................................... Page 8Wiring Diagrams .............................. Page 10Troubleshooting ............................... Page 15Replacement Parts ........................... Page 16Optional Accessories........................ Page 18Warranty Certifi cate.......................... Page 19Installation must conform to local codes.In the absence of local codes, electricalwiring and grounding must comply withthe National Electrical Code ANSI/ NFPA70 - latest edition. In Canada, the currentCSA C22-1 Canadian Electrical Code - latestedition.GENERAL INFORMATIONPower Supply Wire Specifications120 Volt, 60 Hz, 1600 Watts:(ref. Page 10)Hard Wire Connection - Use two conductor,non-metallic sheath cable with ground wire(total three wires) for the incoming powersupply. The wire used must conform to localand national electrical codes for the specifiedpower consumption rating. See Table 1.240 Volt, 60 Hz, 3000 Watt:(ref. Page 11)Use three conductor, non-metallic sheath cablewith ground wire (total four wires) for theincoming power supply. The wire used mustconform to local and national electrical codesfor the specifi ed power consumption rating.See Table 1.Wall Switch or Wall Thermostat Kits(optional kits, see Page 17)Low voltage wire is provided for the wall switchconnection. The wires gage requirements areshown on Table 1.Figure 1LOCATING YOUR IHP ELECTRICFIREPLACEYour new fireplace may be installed into existingframing or built into a wall (see Figure 1).When choosing a location for your new fi re-place, ensure that the general instructions arefollowed. Also, for the best effect, install thefi replace out of direct sunlight and away fromoverhead lighting. See Figure 1.fi replace shown in gray.TOOLS AND BUILDING SUPPLIESNORMALLY REQUIREDTOOLS:Phillips Screwdriver7/16" Socket DriveHammerSaw And/or Saber SawLevelMeasuring TapePlumb LineElectric Drill And BitsPliersSquareGlovesIMPORTANT NOTE: This fi replace systemis not diffi cult to install. However, in theinterest of safety, it is recommended thatthe installer be a qualifi ed or certifi ed“tradesman” familiar with commonlyaccepted fi replace installation and safetytechniques as well as prevailing localcodes.BUILDING SUPPLIES:Framing MaterialsWall Finishing MaterialsCaulking Materials(noncombustible)Top View Showing ApprovedRoom Locations of FireplacePower Supply Wire GageVoltage Wire Gage Fuse120 V 14 GA. 15 AMP240 V 14 GA. 20 AMPWall Switch / Thermostat Wire GageVoltage Wire Gage5 VOLTS 18 GAGETable 1PACKAGING LISTThis assembled Electric Room Heater ispackaged with:• One accessory package located in thefirebox, containing;1. One Installation and Operation Manual.2. One Remote Control.INTRODUCTIONThis Electric Fireplace is designed forresidential applications to be framed in asa zero clearance fireplace.This appliance has been tested in accor-dance with UL 2021 and CSA C22.2 No.46-M198 standards for fi xed and locationdedicated electric room heaters.