IHP CAPELLA 33 Installation And Operation Instructions Manual

Also see for CAPELLA 33: Installation and operation instructions

Contents

IHP CAPELLA 33 Installation And Operation Instructions Manual Manual pdf 7 page image

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 7• When using the remote control, the poweron/off switch inside the body and the wallswitch (optional kit) must be on the OFFposition.REMOTE CONTROL OPERATION:Figure 6The IHP Electric Fireplace is providedwith an Infrared light Remote Control.All functions of the fireplace can be con-trolled through the remote control. Note:The Effective range of the remote controlis up to approximately 26 feet (8 meters).The functions identified on the remote (seeFigure 6) are as follows:A. POWER BUTTONPress once to turn on power to fireplace.B. INDICATING LIGHTIlluminates when signal is sent.C. LIGHT BUTTONOn/off switch for flame and ember light.D. LIGHT ADJUSTING BUTTON (DIM)Reduces brightness of embers.E. LIGHT ADJUSTING BUTTON (BRIGHTEN)Increases brightness of embers.F. HEATER ON/OFFThis button will turn the heater ON and OFFindependent of the main button.G. TEMPERATURE ADJUSTMENT BUTTON(HIGH)Highest heat output, up to 86° F.H. TEMPERATURE ADJUSTMENT BUTTON(MED.)Medium heat output, up to 75° F.I. TEMPERATURE ADJUSTMENT BUTTON(LOW)Lowest heat output, up to 64° F.J. FLAME ADJUSTING BUTTON (LOWER)Reduces fl ame intensity.K. FLAME ADJUSTING BUTTON (HIGHER)Increases fl ame intensity.Remote Control Operation Steps:1. To control the electric fi replace by remotecontrol, the main power on/off switchshould be in the off position. This switch islocated on the front left fl oor of fi rebox (seeFigures 4 & 5).2. When operating the remote control, it mustbe pointed at the logs inside the electricfireplace and a beep must be heard each timeyou press a function button. The beep letsyou know the remote control is operating thefunction button you are pressing.3. Remote On/Off Button - The button on thetop left (see A) is the on/off power button.When pressing this button you will heara beep, this will activate the power to thefi replace. You must then press the displaybutton (C) to activate the lights.Note: If the fl ame does not come on imme-diately, adjust brightness and intensity(buttons E & K).4. To increase the brightness, press and releasethe light brighten button (see E). Each timeyou press this button you will hear a beep,and the brightness will increase slightly untilthe maximum brightness is achieved. Todecrease the brightness, press and releasethe light dimming button (see D). Eachtime you press this button you will heara beep, and the brightness will decreaseslightly until the minimum brightness isachieved.5. Heater Button - To activate the heater, pressthe heater button (see F), then press HI(G),MED (H), or LO (I). The heater is preset tothe following temperatures:• HIGH will shut off when room reachesapproximately 86° F (30° C).• MED. will shut off when room reachesapproximately 75° F (24° C).• LO. (Low) will shut of when room reachesapproximately 64° F (18° C).6. Flame Button - Press the Flame AdjustingButtons to achieve a higher or lower fl ameintensity (see J & K).7. If a yellow fl ame is desired, press andrelease the (K) button until the desired flamecolor is reached. Each time the button isdepressed, you will hear a beep and thefl ame will change from blue to yellow untilthe maximum setting is reached. If a blueflame is desired, press and release the (J)button until the desired color is reached.8. To turn the electric fireplace off, Press theOn/Off button once (A), when you hear thebeep the fireplace will be completely off.When you restart your fireplace with theremote control, all settings will restart at thehigh settings programmed at the factory. Youmay also simply press the (C) button to turnoff the flame and still use the heater.POWERON/OFFON/OFFDISPLAYDimmer BrighterEMBERSHEATER ON/OFFTEMP. CONTROLHIGH MED. LOWFLAMEBLUE YELLOWA CBEFDHG IJ KREMOTE CONTROLCAUTION• Do Not Use Old Batteries WithNew Ones.• Do Not Use Batteries OtherThat The Type Specifi ed (2ea. AA).• Ensure Batteries Are CorrectlyInstalled In Remote Control.