Icom ID-31A PLUS Advanced Manual

Also see for ID-31A PLUS: Manual Manual Basic Manual

Icom ID-31A PLUS Advanced Manual Manual pdf 221 page image

Remote Control functionR-2Remote control (CI-V) informationD Command tableCommand Sub Data Description00 See p. R-3 Send operating frequency for transceive01 See p. R-3 Send operating mode for transceive03 See p. R-3 Read operating frequency04 See p. R-3 Read operating mode05 See p. R-3 Send operating frequency06 See p. R-3 Send operating mode07 Select the VFO mode0C See p. R-3 Read frequency offset*10D See p. R-3 Send frequency offset0F Read duplex setting(10= simplex, 11= DUP–, 12= DUP+)10 Set simplex operation11 Set DUP– operation12 Set DUP+ operation14 01 See p. R-3 Send/Read audio output level03 See p. R-3 Send/Read squelch level0A See p. R-3 Send/Read RF power setting0B See p. R-3 Send/Read external microphone gain16 See p. R-3 Send/Read VOX gain15 01 00 Read noise/S-meter squelch status(squelch close)01 Read noise/S-meter squelch status(squelch open)02 0000 ~ 0255 Read S-meter level (0000= S0, 0170= S9)05 00 Read tone squelch and RF squelch status(squelch close)01 Read tone squelch and RF squelch status(squelch open)11 0000 ~ 0255 Read RF power meter( 0005= S-LOW, 0026= LOW1, 0051=LOW2, 0128= MID, 0255= HIGH)16 42 00 Send/Read Repeater tone OFF01 Send/Read Repeater tone ON43 00 Send/Read Tone squelch OFF01 Send/Read Tone squelch ON02 Send/Read Reversed Tone squelch ON46 00 Send/Read VOX function OFF01 Send/Read VOX function ON4B 00 Send/Read DTCS OFF01 Send/Read DTCS ON02 Send/Read Reversed DTCS ON5B 00 Send/Read DSQL/CSQL OFF (DV modeonly)01 Send/Read DSQL ON (DV mode only)02 Send/Read CSQL ON (DV mode only)5C 00 ~ 02 Send/Read GPS TX mode(00= OFF, 01= D-PRS, 02= NMEA)5D 00 ~ 09 Send Tone setting( 00= OFF, 01= TONE, 02= TSQL,03=DTCS, 04=TSQL-R, 05=DTCS-R,06=DTCS (T), 07=TONE (T)/DTCS (R),08=DTCS (T)/TSQL (R) , 09=TONE (T)/TSQL (R))See ADVANCED MANUAL Section 12about the Tone function.18 00 Turn OFF the transceiver01 Turn ON the transceiver* 219 00 Read transceiver ID.1B 00 See p. R-4 Send/Read Repeater tone frequency01 See p. R-4 Send/Read Tone squelch frequency02 See p. R-4 Send/Read DTCS code and polarity07 See p. R-4 Send/Read CSQL code (DV mode)1C 00 00 Send/Read Transceiver’s status (RX)01 Send/Read Transceiver’s status (TX)Command Sub Data Description1F 00 See p. R-4 Send/Read DV MY call sign01 See p. R-4 Send/Read DV TX call signs02 See p. R-4 Send/Read DV TX message20 00 00 00/01* 3 Send/Read Auto DV RX Call signs output(00= OFF, 01= ON)01 See p. R-5 Output DV RX Call signs for transceive02 See p. R-5 Read DV RX Call signs01 00 00/01* 3 Send/Read Auto DV RX message output(00= OFF, 01= ON)01 See p. R-5 Output DV RX message for transceive02 See p. R-5 Read DV RX message02 00 00/01* 3 Send/Read Auto DV RX status output(00= OFF, 01= ON)01 See p. R-5 Output DV RX status for transceive02 See p. R-5 Read DV RX status03 00 00/01 Send/Read Auto DV RX GPS/D-PRS dataoutput (00= OFF, 01= ON)01 See p. R-6 Output DV RX GPS/D-PRS data fortransceive02 See p. R-6 Read DV RX GPS/D-PRS data fortransceive04 00 00/01 Send/Read Auto DV RX GPS/D-PRSmessage output (00= OFF, 01= ON)01 See p. R-8 Output DV RX GPS/D-PRS message fortransceive02 See p. R-8 Read DV RX GPS/D-PRS message fortransceive22 00 See p. R-8 Send/Read DV TX data (Up to 30 bytes)01 00 00/01 Send/Read Auto DV RX data output(00= OFF, 01= ON)01 See p. R-8 Output DV RX data for transceive(Up to 30 byte)02 00/01 Send/Read DV data TX setting(00= PTT, 01= Auto)03 00/01 Send/Read DV fast data setting(00=OFF, 01= ON)04 00/01 Send/Read GPS Data Speed setting(00= Slow, 01= Fast)05 00 ~ 10 Send/Read TX Delay (PTT) setting(00= OFF, 01= 1 sec. ~ 10= 10 sec.)23 00 See p. R-8 Read the position01 00 Send/Read the internal GPS OFF01 Send/Read the internal GPS ON02 Send/Read the external GPS ON03 Send/Read the manual input02 See p. R-8 Send/read manually input position24 00 00 00/01 Send/read TX output power setting OFF(00=OFF, 01= ON)01 00/01 TX output power setting for transceive(00=OFF, 01= ON)* 1 Less than 100 Hz is omitted.* 2 When sending the power ON command (18 01), the command“FE” must be sent before the basic format.• 19200bps: 48 • 9600bps: 24 • 4800bps: 12• 1200bps: 4 • 300bps: 2q w e r t uFF E×120AEFE E 10810 DFExample: When operating with 4800 bpsq Preamble code (fixed) w Transceiver’s default addresse Controller’s default address r Command numbert Sub command number y End of message code (fixed)* 3 Output setting is automatically turned OFF after turning the powerOFF, then ON.