Jacuzzi Espree Series Installation And Operating Instructions Manual

Contents

Jacuzzi Espree Series Installation And Operating Instructions Manual Manual pdf 15 page image

Cleaning the BathTo clean your bath, simply use a mild, nonabrasiveliquid detergent solution. You can protect and restorethe gloss to a dulled acrylic surface by applyingMeguiar's #10 Mirror Glaze, a product specifically de-signed for use on acrylic finishes. If Meguiar's is notavailable, an acrylic polish of equal quality or automo-tive paste wax is acceptable.Never use abrasive household cleaners on anyJacuzzi Whirlpool Bath product.Repairs to the SurfaceMinor scratches which do not penetrate the color fin-ish can be removed by lightly sanding with 600-grit wet/dry sandpaper. Restore the gloss using Meguiar's Mir-ror Glaze or automotive paste wax.Major scratches and gouges which penetrate theacrylic surface will require refinishing. Ask your JacuzziWhirlpool Bath dealer for special instructions.Purging the Whirlpool SystemNOTE: THE WHIRLPOOL SYSTEM SHOULD BEPURGED AT LEAST TWICE A MONTHTo remove accumulations of bath residue from thewhirlpool system, it is recommended that a whirlpoolbath be purged at least twice a month. For best results,however, we recommend that you purge your whirlpoolbath after each use using our exclusive two-part plum-bing system cleaner made specifically for whirlpoolbaths. Systems Clean ™ is available through an autho-rized Jacuzzi Whirlpool Bath Distributor or by calling usdirect at 1-800-288-4002. Instructions for use: Imme-diately after bathing and exiting the whirlpool bath, leavethe bath water in the tub and add hot water, if necessary,so the water is at least 2" above the highest jet. Turn onthe unit without the aerator. Pour the contents of theSystems Clean Packet 1 (taking care not to get thematerial on yourself) into the bath near the intake for thecirculation pump. Repeat same process with SystemsClean Packet 2. It is important to use Packet 1 beforePacket 2 to avoid a strong odor. Run the bath for 5 to10 minutes. Drain completely and rinse any residue.If you have followed the standard purging instructionsabove and still have an excess accumulation of bathresidue and desire an alternative cleaning mechanism,we recommend SUPER SYSTEMS CLEAN PLUS manu-factured by Stearns Packaging to rectify this condition.This may be obtained by contacting us at l-800-288-4002. It is recommended that you follow the instructionsprovided by the manufacturer with the product. Re-peated use may be necessary. SUPER SYSTEMSCLEAN PLUS does not replace the necessity to regu-larly purge your whirlpool system with Systems Clean asrecommended.(For additional information about water content, contactus for a copy of the Jacuzzi Water Quality Primer.)LampAn optional lamp kit is available from your JacuzziWhirlpool Bath dealer for installation on your bath.When the bulb burns out, replace it from the back ofthe lamp fitting, on the underside of the shell, by pullingout the bulb receptacle. Replacement bulbs (12V, 7W)are available from your Jacuzzi Whirlpool Bath dealer.Bath AdditivesNOTE: DO NOT USE OIL OR OIL BASED BATHADDITIVES.If you want to use any kind of bath additive, use only asmall amount of low-foaming powder or crystal sub-stance; the whirlpool action intensifies the foaming prop-erties of soaps.The use of certain bath oils, bubble baths and bathadditives may increase the level of accumulations ofbath residue in the whirlpool system. If excess accumu-lations persist, you should discontinue use of theseproducts.Suction Cover/Strainer MaintenanceClean the suction cover/strainer of hair and debriswhen necessary. To do this, remove the center screwand detach the square cover. Clean the cover by back-flushing debris from the holes. Replace the suction coverimmediately after cleaning. When reinstalling, orientthe cover/strainer with the small notch at the bottom.The gasket must be inserted into the groove of the cover/strainer before reinstalling onto the suction fitting.CAUTION: Keep hair a minimum of 6 inches awayfrom the suction fitting at all times when the whirl-pool system is operating. Hair longer than shoul-der length should be secured close to the head, ora bathing cap should be worn. Do not operate thewhirlpool system with the suction cover removed!It is a safety device and must always be in place onthe suction fitting to minimize the potential hazardof hair and body entrapment.NOTCH GASKETCOVER STRAINERSCREWSUCTIONFITTINGSUCTION COVER/STRAINER ASSEMBLYMAINTENANCELIGHT BULB REPLACEMENTLIGHT BULBLIGHT BEZELBATH SHELLBULB RECEPTACLELOCKING NUT11Jacuzzi Whirlpool Bath© U961000F 12/04