Contents - pressure washer
- Machine Data Label
- Table Of Contents
- how to use this manual
- important safety information
- Propane Tank Safety Instructions
- Component Identification - All Models
- Installation HDS 6.3/32, 8.0/32, 9.5/30
- gas piping
- Pipe Sizing Chart for Natural Gas
- Room Vents for Combustion and Ventilation Air
- water source
- Gas Valve Replacement
- for your safety
- check list before starting
- assembly instructions
- operating instructions
- Operating Techniques
- after extended storage
- Maintenance
- unloader valves
- Gas Valve Regulator Adjustment
- propane gas
- Burner Basic Facts
- oil change record
- preventative maintenance
- troubleshooting
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Frame
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Burner
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Coil
- HDS 6.3/32, 8.0/32, 9.5/30 Frame
- HDS 6.3/32, 8.0/32, 9.5/30 Burner
- HDS 6.3/32, 8.0/32, 9.5/30 Coil
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Float Tank
- HDS 6.3/32, 8.0/32, 9.5/30 Float Tank
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Pump
- HDS 6.3/32, 8.0/32, 9.5/30 Pump
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Tensioner
- HDS 6.3/32, 8.0/32, 9.5/30 Tensioner
- Tensioner Torque Specs & Assembly Parts
- HDS 6.3/32, 8.0/32, 9.5/30 Electrical Box
- Panel
- HDS 6.3/32, 8.0/32, 9.5/30 Control Panel
- Doors
- HDS 6.3/32, 8.0/32, 9.5/30 Panels & Doors
- Hose & Spray Gun
- Specifications
- Motor
- Controls
- VRT3 Unloader
- vrt3 unloader
- VRT100 Unloader
- HDS 4.0/22, 3.9/30 M.3 Series Pump
- HDS 5.0/23, 4.8/30, 6.3/32 KT.2 Series Pump
- HDS 8.0/32, 9.5/30 X.2 Series Pump
- HDS 3.5/20 KB Series Pump
| 
20OperationsCheck List Before Starting:CAUTION! If “NO” has been checked on any of thefollowing sixteen questions, do not operate thismachine.ATTENTION : Si la réponse à l'une des questionsci-dessus est « NON », ne pas utiliser la machine.YES NOHas gas supply been inspected by anauthorized contractor to meet localcodes?Is machine protected from downdraftand excessive wind?Is machine shielded from moisture orwater spray?Is the voltage correct and are the circuitbreaker and supply cord adequateaccording to specifications and serialplate notation?Is the machine electrically grounded?Is there ample water supply?Have all flammable liquids or gasesbeen removed from installationlocation?Is there adequate gas supply for theBTU rating of the burner?"Is incoming gas supply pressurebetween 6" - 14" water column inches or1/2 PSIG?"Has the proper gas regulator beeninstalled for pressure and volume?Have you installed the optional LP gasregulator assembly 9.802-633.0?Is the machine properly vented to allowadequate air flow?Are the propane tanks large enough,according to rating to prevent freezing?Have gas lines been checked for gasleaks?Have gas lines been checked with localcodes?Have all operators using this machinebeen instructed properly and have theyread the manual?Has the machine been installedaccording to operator's manual instruc-tions?Karcher Liberty HDS Stationary Dealer’s Manual 9.801-508.0 - AY |
