Contents - pressure washer
- Machine Data Label
- Table Of Contents
- how to use this manual
- important safety information
- Propane Tank Safety Instructions
- Component Identification - All Models
- Installation HDS 6.3/32, 8.0/32, 9.5/30
- gas piping
- Pipe Sizing Chart for Natural Gas
- Room Vents for Combustion and Ventilation Air
- water source
- Gas Valve Replacement
- for your safety
- check list before starting
- assembly instructions
- operating instructions
- Operating Techniques
- after extended storage
- Maintenance
- unloader valves
- Gas Valve Regulator Adjustment
- propane gas
- Burner Basic Facts
- oil change record
- preventative maintenance
- troubleshooting
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Frame
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Burner
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Coil
- HDS 6.3/32, 8.0/32, 9.5/30 Frame
- HDS 6.3/32, 8.0/32, 9.5/30 Burner
- HDS 6.3/32, 8.0/32, 9.5/30 Coil
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Float Tank
- HDS 6.3/32, 8.0/32, 9.5/30 Float Tank
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Pump
- HDS 6.3/32, 8.0/32, 9.5/30 Pump
- HDS 3.5/20, 4.0/22, 3.9/30, 5.0/23, 4.8/30 Tensioner
- HDS 6.3/32, 8.0/32, 9.5/30 Tensioner
- Tensioner Torque Specs & Assembly Parts
- HDS 6.3/32, 8.0/32, 9.5/30 Electrical Box
- Panel
- HDS 6.3/32, 8.0/32, 9.5/30 Control Panel
- Doors
- HDS 6.3/32, 8.0/32, 9.5/30 Panels & Doors
- Hose & Spray Gun
- Specifications
- Motor
- Controls
- VRT3 Unloader
- vrt3 unloader
- VRT100 Unloader
- HDS 4.0/22, 3.9/30 M.3 Series Pump
- HDS 5.0/23, 4.8/30, 6.3/32 KT.2 Series Pump
- HDS 8.0/32, 9.5/30 X.2 Series Pump
- HDS 3.5/20 KB Series Pump
|
21OperationsAssembly InstructionsSTEP 1: Attach the high pressurehose to the spray gun using teflontape on hose threads.STEP 4: Connect the garden hoseto pump water inlet. Inspect inlets.CAUTION: Do not run the pumpwithout water or pump damagewill result.STEP 2: Connect the high pressurehose to the discharge fitting. Twisthose connector clockwise until tighton thread fitting.STEP 5: Before installing nozzle,turn on the water supply and runmachine allowing water to run fromthe end of the wand until clear.Turn off machine.STEP 3: Connect garden hose tothe cold water source.STEP 6: Attach the Power Nozzleto end of the wand as shown inpicture.SafetyLatchSprayGunHigh PressureHosePumpWater InletGardenHosePump DischargeThread FittingM22HighPressureHoseColdWaterSourceGardenHosePressureNozzleWandGuardKarcher Liberty HDS Stationary Dealer’s Manual 9.801-508.0 - AY PreviousNext |