20 English English 21CONTENTSSelecting the Bluetooth Device1 Press to enter Bluetooth mode.2 Turn the volume knob to select[SETTINGS], then press to enter.3 Turn the volume knob to select[PAIRING], then press to enter.4 Turn the volume knob to select [PHONESELECT]/ [PHONE SEL] or [AUDIOSELECT]/ [AUDIO SEL], then press toenter.5 Turn the volume knob to select aBluetooth device name.6 Press the volume knob to set up theBluetooth device.■■ “✱ (device name)”: The selectedBluetooth device is busy.■■ “- (device name)”: The selected Bluetoothdevice is on standby.■■ “(blank) (device name)“: The Bluetoothdevice is deselected.■■ If two cell-phones or an audio playerhave already been selected, deselect onedevice before selecting a new Bluetoothdevice.7 Hold to finish the procedure.■■ To cancel the Bluetooth mode, press .Bluetooth Device Registration TestYou can check whether your Bluetooth devicecan be registered using this unit.1 Press and hold to enter pairing mode“PAIRING” is displayed.2 “PLEASE PAIR YOUR PHONE” is displayed.■■ When “(device name)” is displayed, select"[PAIRING]" and press the control knob.■■ When “DEVICE FULL” is displayed, delete aBluetooth device and retry.1. Turn the volume knob to select theBluetooth device, then press and holdto confirm.2. Turn the volume knob to select “YES”,then press to confirm.3 Start registering this unit by operatingthe Bluetooth device.By operating the Bluetooth device, registerthe hands-free unit or audio unit (pairing).Select “KENWOOD BT CD/R-5T1” from thelist of found units.4 Input the PIN code (“0000”) in theBluetooth device.Check that registration is complete onthe Bluetooth device. PIN code is set to“0000” as the default. You can change thiscode. Refer to [PIN CODE EDIT] under (page 20).5 “(device name)” is displayed. Press andhold the volume knob.“BT TEST” is displayed.6 The connection result, “OK” or “NG”, isdisplayed.■■ “PAIRING”: Registration to this unit■■ “HF CNT”: Hands-free phoning■■ “AUD CNT”: Audio playback■■ “PB DL”: Phone Book downloading7 Press to exit pairing mode.■■ Data (Phone Book, etc.) of the cell-phonechecked for connection does not remain inthis unit.Bluetooth Setup1 Press to enter Bluetooth mode.2 Turn the volume knob to select[SETTINGS], then press to enter.3 Turn the volume knob to make aselection, then press to confirm.■■ See table below for selection.■■ Repeat step 3 until the desired item isselected/activated.■■ Press to return to the previous item.4 Hold to finish the procedure.■■ To cancel the Bluetooth mode, press .Bluetooth Setup Item Selectable setting (Preset: *)PAIRINGPHONE SELECT/PHONE SELSelects a cell-phone connection.(For details, see page 20.)AUDIO SELECT/AUDIO SELSelects a Bluetooth audio player connection.(For details, see page 20.)DEVICE DELETE/DVC DELETECancel registration of the Bluetooth device.1. Turn the volume knob to select the Bluetooth device, then press to confirm.2. Turn the volume knob to select “YES”, then press to confirm. “DELETE” is displayed.TRANSFER PB (For details, see page 18.)DETAILED SET/DETAIL SETPIN CODE EDIT/PIN EDITSpecify the PIN code required when registering this unit using the Bluetooth device. By default, “0000” isspecified.1. Turn the volume knob to select the number.■■ To move to the next digit, press ¢.■■ To delete the last digit, press 4.2. Press the volume knob to register a PIN code. “COMPLETED” is displayed.AUTO ANSWER OFF: Does not answer the phone call automatically. ; 0: Automatically answers the phone call at once. ;1 – 8 * –99: Automatically answers the phone call after lapse of 1 – 99 seconds.RECONNECT/RECONCTON *: Automatically reconnects the selected Bluetooth device when radio wave becomes strong enough,even after it is disconnected. ; OFF: Cancels.■■ When this function is turned ON, the Bluetooth device is reconnected if it has been disconnected byselecting [PHONE SELECT]/ [PHONE SEL]/ [AUDIO SELECT]/ [AUDIO SEL].BT HF/AUDIO FRONT *: Outputs audio from the front-left and front-right speakers. ;ALL: Outputs audio from the all speakers.CALL BEEP ON *: Sets whether to output a beep from the speaker when a call comes in. ; OFF: Cancels.BT F/W UPDATE/BT UPDATEDisplay the firmware version and update the firmware.MIC GAIN 1 — 8 * — 15: Adjust the sensitivity of the microphone for telephone call or adjusts the voice of the caller.(KDC-BT42U: The default is 12 when [MIC SELECT] is set to [EXT].)MIC SELECT KDC-BT42U onlyDetermines whether the built-in or external microphone is to be used when the receiver incorporates amicrophone. IN *: Use the built-in microphone. ; EXT: Use the external microphone.
