14 English English 15CONTENTSPARiPodVOICEPress and hold to pairing mode.Getting Started of BluetoothRegistering your Bluetooth devicewith this unit (Pairing)1 Press and hold to enter pairing mode“PAIRING” is displayed.■■ Any of the following is displayeddepending on Bluetooth deviceregistration condition:– “PLEASE PAIR YOUR PHONE”: Whenregistering a Bluetooth device for thefirst time.– “(device name)”: When a Bluetoothdevice has already been registered.– “DEVICE FULL”: When a maximum of fiveBluetooth devices have already beenregistered.■■ To cancel the pairing mode, press .When registering a Bluetooth device for thefirst time (Registering a Bluetooth device)2 “PLEASE PAIR YOUR PHONE” is displayed.3 Start registering this unit by operatingthe Bluetooth device.By operating the Bluetooth device, registerthe hands-free unit or audio unit (pairing).Select “KENWOOD BT CD/R-5T1” from thelist of found units.4 Input the PIN code (“0000”) in theBluetooth device.Check that registration is complete onthe Bluetooth device. PIN code is set to“0000” as the default. You can change thiscode. Refer to [PIN CODE EDIT] under (page 20).5 “(device name)” is displayed. Press thevolume knob.6 The receiver is connected to a Bluetoothdevice, with “HF CONNECT” or “AUDCONNECT” displayed, and exits thepairing mode.■■ If an error code is displayed during paring,see (page 31).When a Bluetooth device has already beenregistered, or maximum of five Bluetoothdevices have already been registered(Selecting a Bluetooth device)2 “(device name)” or “DEVICE FULL” isdisplayed.3 Turn the volume knob to select aBluetooth device name.■■ To register a new Bluetooth device, select“[PAIRING]”, then go to “When registeringa Bluetooth device for the first time.”4 Press the volume knob.5 Turn the volume knob to select theprofile for the device to connect.■■ “HANDSFREE”/ ”AUDIO”: The device canbe connected using either a hands-freeor audio profile.“HF/AUD”: The device is can be connectedusing both hands-free and audio profiles.6 Press the volume knob to set up theBluetooth device.■■ “✱H✱A (device name)”: The selectedBluetooth device is busy.■■ “-H-A (device name)”: The selectedBluetooth device is on standby.■■ “(blank) (device name)“: The Bluetoothdevice is deselected.■■ If two cell-phones or an audio playerhave already been selected, deselect onedevice before selecting a new Bluetoothdevice.• “H” (HFP) or “A” (A2DP) indicates thecorresponding profile.7 Press to exit pairing mode.Deleting the registered Bluetooth device2 “(device name)” or “DEVICE FULL” isdisplayed.3 Turn the volume knob to select aBluetooth device name.4 Press and hold the volume knob to deletethe selected cell-phone.“DELETE” is displayed.5 Turn the volume knob to select “YES”,then press to confirm.“COMPLETED” is displayed.6 Press to exit easy pairing mode.Registering from Bluetooth devices(Pairing)1 Press SRC to turn on the power.2 Start registering this unit by operatingthe Bluetooth device.By operating the Bluetooth device, registerthe hands-free unit or audio unit (pairing).Select “KENWOOD BT CD/R-5T1” from thelist of found units.3 Input the PIN code (“0000”) in theBluetooth device.Check that registration is complete onthe Bluetooth device. PIN code is set to“0000” as the default. You can change thiscode. Refer to [PIN CODE EDIT] under (page 20).4 By operating the Bluetooth device, starthands-free connection.■■ If there are 5 or more Bluetooth devicesregistered, you cannot register a newBluetooth device.About the Cell-Phone■■ Version: Bluetooth Standard Ver. 2.1+EDR■■ Profile:HFP (Hands Free Profile)SPP (Serial Port Profile)OPP (Object Push Profile)PBAP (Phone book Access Profile)A2DP (Advanced Audio Distribution Profile)AVRCP (Audio/Video Remote ControlProfile)For the cell-phones verified for compatibility,access the following URL:www.kenwood.com/cs/ce/bt/■■ The units supporting the Bluetoothfunction have been certified for conformitywith the Bluetooth Standard following theprocedure prescribed by Bluetooth SIG.However, it may be impossible for suchunits to communicate with your cell-phone depending on its type.
