32 English English 33CONTENTSBluetoothSymptom Remedy/CauseThe hands-free talk volume is low. The hands-free talk volume can be adjusted independently. Adjust it during hands-free talk.[MIC GAIN] of (page 20).No beep is heard at reception of anincoming call.No beep is heard depending on the type of your cell-phone. The [CALL BEEP] of Setup> (page 20) is set ON.Voice is not recognized. ■■ The vehicle window is open. If the surrounding noise is large, voice cannot be recognizedproperly. Close the vehicle windows to reduce noise.■■ Small voice. If voice is too small, it cannot be recognized properly. Speak into the microphonea little more loudly and naturally.■■ The person uttering the voice tag is not the one who registered the it. Only the voice of theperson who registered the voice tag can be recognized.“NO NUMBER” appears. The calling party does not notify a caller ID. / There is no phone number data.“NO DATA” appears. There is no outgoing call list. / There is no incoming call list. / There is no missed call list. / Thereis no phone book list. / Data is not contained in the phone book.“NO ENTRY” appears. The cell-phone has not been registered (pairing).“HF DISCONCT” appears. The unit cannot communicate with the cell-phone.“AUD DISCONCT” appears. The unit cannot communicate with the audio player.“HF ERROR 07” appears. The memory cannot be accessed. Turn off the power and on again. If this message still appears,press the reset button on the control unit.“HF ERROR 68” appears. The unit cannot communicate with the cell-phone. Turn off the power and on again. If thismessage still appears, press the reset button on the control unit.“HF ERROR 89” appears. Update of the Bluetooth firmware has failed. Retry it.“UNKNOWN” appears. The Bluetooth device cannot be detected.“DEVICE FULL” appears. 5 Bluetooth device have already been registered. No more Bluetooth device cannot beregistered.“PIN CODE NG” appears. The PIN code is wrong.“CONNECT NG” appears. The unit cannot be connected to the device.“PAIRING NG” appears. Pairing error.“NO ACTIVE DVC”/ “NO ACT DVC”appears.No cell-phone is connected. Connect your cell-phone before starting voice recognition.The sound from the Bluetoothaudio player is discontinuous.■■ Another Bluetooth device is affecting the Bluetooth communication. Turn off anotherBluetooth device. Move another Bluetooth device away from this unit.■■ Another Bluetooth device or profile is used for communication. The downloading of thePhone book disconnects the sound.SpecificationsFM tuner sectionFrequency range (50 kHz space):87.5 MHz — 108.0 MHzUsable sensitivity (S/N= 26 dB):1 μV/ 75 ΩQuieting sensitivity (DIN S/N = 46 dB):2.5 μV/75 ΩFrequency response (±3 dB): 30 Hz — 15 kHzSignal-to-Noise ratio (MONO): 63 dBStereo separation (1 kHz): 40 dBMW tuner sectionFrequency range (9 kHz space): 531 kHz – 1,611 kHzUsable sensitivity (S/N = 20dB): 36 μVLW tuner sectionFrequency range: 153 kHz – 279 kHzUsable sensitivity (S/N = 20dB): 57 μVCD player sectionLaser diode: GaAIAsDigital filter (D/A): 8 Times Over SamplingD/A converter: 24 BitSpindle speed: 500 rpm — 200 rpm (CLV)Wow & Flutter: Below Measurable LimitFrequency response (±1 dB): 20 Hz — 20 kHzTotal harmonic distortion (1 kHz): 0.01 %Signal-to-Noise ratio (1 kHz): 105 dBDynamic range: 93 dBAAC decode: AAC-LC “.m4a” filesMP3 decode: Compliant with MPEG-1/2 AudioLayer-3WMA decode: Compliant with Windows MediaAudioUSB interfaceUSB standard: USB1.1/ 2.0 (Full speed)Maximum supply current:DC 5 V 1 AFile system: FAT16/ 32AAC decode: AAC-LC “.m4a” filesMP3 decode: Compliant with MPEG-1/2 AudioLayer-3WMA decode: Compliant with Windows MediaAudioBluetooth sectionTechnology: Bluetooth Ver. 2.1+EDR CertifiedFrequency: 2.402 GHz – 2.480 GHzOutput Power: +4 dBm (MAX), 0 dBm (AVE)Power Class 2Maximum Communication range:Line of sight approx. 10m (32.8 ft)Profile:HFP (Hands Free Profile),SPP (Serial Port Profile),OPP (Object Push Profile),PBAP (Phonebook Access Profile),A2DP (Advanced Audio DistributionProfile),AVRCP (Audio/Video Remote ControlProfile)Audio sectionMaximum output power: 50 W × 4Output power (DIN 45324, +B=14.4V): 30 W × 4Speaker impedance: 4 Ω — 8 ΩTone action:Bass: 100 Hz ±8 dBMiddle: 1 kHz ±8 dBTreble: 12.5 kHz ±8 dBPreout level / load (CD): 2,500 mV/ 10 kΩPreout impedance: ≤ 600 ΩAuxiliary input sectionFrequency response (±3 dB): 20 Hz — 20 kHzInput maximum voltage: 1,200 mVInput impedance: 10 kΩGeneralOperating voltage:14.4 V (10.5 V — 16 V allowable)Maximum current consumption: 10 AInstallation size (W × H × D):182 mm × 53 mm × 160 mmWeight: 1.3 kgSubject to change without notice.
