Kenwood KRF-V8060D Instruction Manual

Also see for KRF-V8060D: Service manual Service manual Instruction manual Instruction manual

Contents

20 ENPreparing for surround soundSpeaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.SETUP MULTI CONTROLPOWER ON/OFF(KRF-V8060D)POWERSET UP Joystick(MULTI CONTROL 5 / ∞,DOWN 2 / UP3)POWERON/STANDBY(VR-6060)ON/STANDBY(KRF-V8060D)1Turn on the power to this receiver by pressing the POWERON/STANDBY (for VR-6060) or POWER ON/OFF and ON/STANDBY (for KRF-V8060D) key or POWER key.2Press the SETUP key to enter the SETUP mode.The Surround Back and Subwoofer speaker output selections aredisplayed as follows:1 6ch AMP SB2 6ch AMP SWUse the MULTI CONTROL knob or Joystick (5/∞) to select the speakers.Press the SETUP key to proceed to the next SET UP selection.Use MMMMM/?????keys or Joystick (2/ 3) for the following displays.1 SP SETUP2 TEST TONE3 SP DISTANCE4 DISP MODE5 EXITThe flow of the SET UP is as follows:SP SETUP TEST TONE SP DISTANCE EXITDISP MODEFront LeftCenterFront RightSurround RightSurround BackSurround LeftSubwooferDisplay SelectorDisplay ListenSubwooferFrontCenterSurroundSurroundBackSurroundMixSubwooferRe-mixT. TONEMANUALT. TONEAUTOLCRSRSLSBSWLCRSRSLSWSB3Select a speaker system.1 Select the SP SETUP and press the SETUP key again sothat the subwoofer setting indication “SUBW ON” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE2 Use the MULTI CONTROL knob or Joystick (5/∞) to selectthe appropriate subwoofer setting.1 SUBW ON : Subwoofer setting mode to the receiver isON.2 SUBW OFF : Subwoofer setting mode to the receiver isOFF.• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the front speakersare automatically set to “FRNT LARGE” and the procedure skipsto step 6.Before step 6, press the SETUP key to accept the setting.• When subwoofer output sound is required, select “FRNTNORMAL”, or select both “FRNT LARGE” and “SW RE-MIX ON”.• After setting SW (subwoofer) from OFF to ON, 6ch AMP setupdisplay will appear to enable you to re-select either SW or SB fromthe surround back or subwoofer speaker terminal.3 Press the MMMMM key or Joystick (3) to accept the setting.• The front speakers setting indication “FRNT” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE4 Use the MULTI CONTROL knob or Joystick (5/∞) to selectthe appropriate front speakers setting.1 FRNT LARGE : Large front speakers are connectedto the receiver.2 FRNT NORMAL : Average size front speakers are con-nected to the receiver.• For “FRNT LARGE” selection, no sound will be heard fromsubwoofer speaker even when it is set to ON. However, if youselect “SW RE-MIX ON” when subwoofer is selected, you willbe able to hear sound from the subwoofer.When in STEREO mode, the sound goes directly to frontspeaker.5 Press the MMMMM key or Joystick (3) to accept the setting.• The center speaker setting indication “CNTR” appears.6 Use the MULTI CONTROL knob or Joystick (5/∞) to selectthe appropriate center speaker setting.If you selected “LARGE” as the front speakers setting,1 CNTR LARGE : A large center speaker is connectedto the receiver.2 CNTR NORMAL : An average size center speaker isconnected to the receiver.3 CNTR OFF : Center speaker setting mode to thereceiver is OFF.If you selected “NORMAL” as the front speakers setting,1 CNTR ON : Center speaker setting mode to the re-ceiver is ON.2 CNTR OFF : Center speaker setting mode to the re-ceiver is OFF.7 Press the MMMMM key or Joystick (3) again to accept the setting.• The surround speaker setting indication “SURR” appears.8 Use the MULTI CONTROL knob or Joystick (5/∞) to selectthe appropriate surround speaker setting.If you selected “LARGE” as the center speaker setting,1 SURR LARGE : Large surround speakers are con-nected to the receiver.2 SURR NORMAL : Average size surround speakers areconnected to the receiver.3 SURR OFF : Surround speaker setting mode tothe receiver is OFF.