NX-200(G)56-2. Connection procedureConnect the transceiver to the personal computer usingthe interface cable (KPG-36A/36U). (Connection is the sameas in the PC Mode.)6-3. Programming1. Start up the firmware programming software (Fpro.exe(Ver. 6.20 or later)). The Fpro.exe exists in the KPG-111D/111DN installed holder.2. Set the communications speed (normally, 115200 bps)and communications port in the confi guration item.3. Set the fi rmware to be updated by File name item.4. Press and hold the [ ] key while turning the transceiverpower ON. Then, the orange LED on the transceiverlights and “PROGRAM 115200” is displayed.5. Check the connection between the transceiver and thepersonal computer, and make sure that the transceiver isin the Program mode.6. Press “write” button in the window. When the transceiverstarts to receive data, the [LOADING] display lights.7. If writing ends successfully, the checksum is calculatedand a result is displayed.8. If you want to continue programming other transceivers,repeat steps 4 to 7.Note:This mode cannot be entered if the Firmware Program-ming mode is set to Disable in the Programming soft-ware.6-4. Function1. If you press the [Side2] key while “PROGRAM 115200”is displayed, the display changes to “PROGRAM 19200”(The LED blinks green) to indicate that the write speedis low speed (19200 bps). If you press the [Side2] keyagain while “PROGRAM 19200” is displayed, the displaychanges to “PROGRAM 38400” (The LED lights redand orange alternatively). If you press the [Side2] keyagain while “PROGRAM 38400” is displayed, the displaychanges to “PROGRAM 57600” (The LED blinks orange).If you press the [Side2] key again while “PROGRAM57600” is displayed, the display returns to “PROGRAM115200” (The LED lights orange).2. If you press the [Side1] key while “PROGRAM 115200”is displayed, the checksum is calculated, and a result isdisplayed. If you press the [Side1] key again while thechecksum is displayed, “PROGRAM 115200” is redis-played.Note:Normally, write in the high-speed mode.7. Clone ModeProgramming data can be transferred from one transceiv-er to another by connecting them via their external universalconnectors. The operation is as follows (the transmit trans-ceiver is the source and the receive transceiver is a target).The following data cannot be cloned.• Tuning data• Embedded message with password• Model name data• ESN (Electronic Serial Number) dataNote:The following data can be cloned.• Fleet (own)/ID (own) for FleetSync• Unit ID (own) for NXDNKey guide on the Read authorization password input screen.• CONFRM ([ ] key): The password confi rmation• DELETE ([ ] key): Delete the least digit from the currentpassword number (Press and hold to delete all passwordnumbers)• SELECT ([ ] key): Determine the least digit of the pass-word number1. Press and hold the [ ] key while turning the transceiverpower ON. If the Read authorization password is set tothe transceiver, the transceiver displays “CLONE LOCK”.If the password is not set, the transceiver displays “CLONEMODE”.2. When you enter the correct password, and “CLONEMODE” is displayed, the transceiver can be used as thecloning source. The following describes how to enter thepassword.3.• How to enter the password using the keypad (K2model only);If one of keys 0 to 9 is pressed while the “CLONE LOCK”is displayed, the pressed number is displayed on theLCD.Each press of the key shifts the display in order to theleft.When you enter the password and press the [ ] or [ ]key, “CLONE MODE” is displayed if the entered passwordis correct. If the password is incorrect, “CLONE LOCK” isredisplayed.• How to enter the password using the [ ] and [ ]keys ;If the [ ] / [ ] key is pressed while “CLONE LOCK” isdisplayed, the Read authorization password input screenis displayed.If the [ ] key or [ ] key is pressed while the Readauthorization password input screen is displayed, thenumber (0 to 9) blinks on the LCD. When you press the[ ] key, the currently selected number is determined. Ifyou press the [ ] key after entering the password in thisprocedure, “CLONE MODE” is displayed if the enteredpassword is correct. If the password is incorrect, “CLONELOCK” is redisplayed.REALIGNMENT